Malzeme
- Çalışma Grubu
- Laboratuvarlar
- Bilimsel Yayınlar
- Projeler
| Doç. Dr. Sinan Kandemir | Araş. Gör. Senagül Tunca Taşkıran | |||
| Prof. Dr. Metin Tanoğlu | ||||
| Dr. Öğr. Üyesi M. Fatih Toksoy |
Kompozit Araştırma Laboratuvarı
Kompozit Malzeme Laboratuvarı
Malzeme Karakterizasyonu Laboratuvarı
Metal İşleme Laboratuvarı
Metalografi Laboratuvarı
Sorumlu Öğretim Üyesi
- Makina Mühendisliği Binası (148)
- +90 232 750 6747
Toz Metalurji Laboratuvarı
2023 |
İplikçi, Hande; Barisik, Murat; Türkdoğan, Ceren; Martin, Seçkin; Yeke, Melisa; Nuhoğlu, Kaan; Esenoğlu, Gözde; Tanoğlu, Metin; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet Erdem Effects of nanosecond laser ablation parameters on surface modification of carbon fiber reinforced polymer composites Journal Article Journal of Composite Materials, 57 (18), pp. 2843 – 2855, 2023. @article{İplikçi20232843, title = {Effects of nanosecond laser ablation parameters on surface modification of carbon fiber reinforced polymer composites}, author = {Hande İplikçi and Murat Barisik and Ceren Türkdoğan and Seçkin Martin and Melisa Yeke and Kaan Nuhoğlu and Gözde Esenoğlu and Metin Tanoğlu and Engin Aktaş and Serkan Dehneliler and Mehmet Erdem İriş}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85162945413&doi=10.1177%2f00219983231178892&partnerID=40&md5=1e698a002a7d62e7f42a2444aafff1d5}, doi = {10.1177/00219983231178892}, year = {2023}, date = {2023-01-01}, journal = {Journal of Composite Materials}, volume = {57}, number = {18}, pages = {2843 – 2855}, abstract = {Removal of contaminants and top polymer layer from the surface of carbon-fiber-reinforced polymer (CFRP) composites is critical for high-quality adhesive-joining with direct bonding to the reinforcing fiber constituents. Surface treatment with a laser beam provides selective removal of the polymer matrix without damaging the fibers and increasing the wettability. However, inhomogeneous thermal properties of CFRP make control of laser ablation difficult as the laser energy absorbed by the carbon fibers is converted into heat and transmitted through the fiber structures during the laser operation. In this study, the effect of scanning speed and laser power on nanosecond laser surface treatment was characterized by scanning electron microscope images and wetting angle measurements. Low scanning speeds allowed laser energy to be conducted as thermal energy through the fibers, which resulted in less epoxy matrix removal and substantial thermal damage. Low laser power partially degraded the epoxy the surface while the high power damaged the carbon fibers. For the studied CFRP specimens consisting of unidirectional [45/0/−45/90]2s stacking of carbon/epoxy prepregs (HexPly®-M91), 100 mJ/mm2 generated by 10 m/s scanning speed and 30 W power appeared as optimum processing parameters for the complete removal of epoxy matrix from the top surface with mostly undamaged carbon fibers and super hydrophilic surface condition. © The Author(s) 2023.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Removal of contaminants and top polymer layer from the surface of carbon-fiber-reinforced polymer (CFRP) composites is critical for high-quality adhesive-joining with direct bonding to the reinforcing fiber constituents. Surface treatment with a laser beam provides selective removal of the polymer matrix without damaging the fibers and increasing the wettability. However, inhomogeneous thermal properties of CFRP make control of laser ablation difficult as the laser energy absorbed by the carbon fibers is converted into heat and transmitted through the fiber structures during the laser operation. In this study, the effect of scanning speed and laser power on nanosecond laser surface treatment was characterized by scanning electron microscope images and wetting angle measurements. Low scanning speeds allowed laser energy to be conducted as thermal energy through the fibers, which resulted in less epoxy matrix removal and substantial thermal damage. Low laser power partially degraded the epoxy the surface while the high power damaged the carbon fibers. For the studied CFRP specimens consisting of unidirectional [45/0/−45/90]2s stacking of carbon/epoxy prepregs (HexPly®-M91), 100 mJ/mm2 generated by 10 m/s scanning speed and 30 W power appeared as optimum processing parameters for the complete removal of epoxy matrix from the top surface with mostly undamaged carbon fibers and super hydrophilic surface condition. © The Author(s) 2023. |
Nuhoğlu, Kaan; Aktaş, Engin; Tanoğlu, Metin; Martin, Seçkin; İplikçi, Hande; Barışık, Murat; Yeke, Melisa; Türkdoğan, Ceren; Esenoğlu, Gözde; Dehneliler, Serkan; İriş, Mehmet Erdem Analysis of adhesively bonded joints of laser surface treated composite primary components of aircraft structures Journal Article International Journal of Adhesion and Adhesives, 126 , 2023. @article{Nuhoğlu2023, title = {Analysis of adhesively bonded joints of laser surface treated composite primary components of aircraft structures}, author = {Kaan Nuhoğlu and Engin Aktaş and Metin Tanoğlu and Seçkin Martin and Hande İplikçi and Murat Barışık and Melisa Yeke and Ceren Türkdoğan and Gözde Esenoğlu and Serkan Dehneliler and Mehmet Erdem İriş}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85166291425&doi=10.1016%2fj.ijadhadh.2023.103456&partnerID=40&md5=aa5024e2ac1955cb1a3ff85d46fc3589}, doi = {10.1016/j.ijadhadh.2023.103456}, year = {2023}, date = {2023-01-01}, journal = {International Journal of Adhesion and Adhesives}, volume = {126}, abstract = {The performance of the adhesively bonded aerospace structures highly depends on the adhesion strength between the adhesive and adherents, which is affected by, in particular, the condition of the bonding surface. Among the various surface treatment methods, as state of the art, laser surface treatment is a suitable option for the CFRP composite structures to enhance the adhesion performance, adjusting the roughness and surface free energy with relatively minimizing the damage to the fibers. The aim of this study is the validation and evaluation of the adhesive bonding behavior of the laser surface-treated CFRP composite structures, using the finite element technique to perform a conservative prediction of the failure load and damage growth. Such objectives were achieved by executing both experimental and numerical analyses of the secondary bonded CFRP parts using a structural adhesive. In this regard, to complement physical experiments by means of numerical simulation, macro-scale 3D FEA of adhesively bonded Single Lap Joint and Skin-Spar Joint specimens has been developed employing the Cohesive Zone Model (CZM) technique in order to simulate bonding behavior in composite structures especially skin-spar relation in the aircraft wing-box. © 2023 Elsevier Ltd}, keywords = {}, pubstate = {published}, tppubtype = {article} } The performance of the adhesively bonded aerospace structures highly depends on the adhesion strength between the adhesive and adherents, which is affected by, in particular, the condition of the bonding surface. Among the various surface treatment methods, as state of the art, laser surface treatment is a suitable option for the CFRP composite structures to enhance the adhesion performance, adjusting the roughness and surface free energy with relatively minimizing the damage to the fibers. The aim of this study is the validation and evaluation of the adhesive bonding behavior of the laser surface-treated CFRP composite structures, using the finite element technique to perform a conservative prediction of the failure load and damage growth. Such objectives were achieved by executing both experimental and numerical analyses of the secondary bonded CFRP parts using a structural adhesive. In this regard, to complement physical experiments by means of numerical simulation, macro-scale 3D FEA of adhesively bonded Single Lap Joint and Skin-Spar Joint specimens has been developed employing the Cohesive Zone Model (CZM) technique in order to simulate bonding behavior in composite structures especially skin-spar relation in the aircraft wing-box. © 2023 Elsevier Ltd |
Esenoğlu, Gözde; Tanoğlu, Metin; Barisik, Murat; İplikçi, Hande; Yeke, Melisa; Nuhoğlu, Kaan; Türkdoğan, Ceren; Martin, Seçkin; Aktaş, Engin; Dehneliler, Serkan; Gürbüz, Ahmet Ayberk; İriş, Mehmet Erdem Investigating the Effects of PA66 Electrospun Nanofibers Layered within an Adhesive Composite Joint Fabricated under Autoclave Curing Journal Article ACS Omega, 8 (36), pp. 32656 – 32666, 2023, (All Open Access, Gold Open Access, Green Open Access). @article{Esenoğlu202332656, title = {Investigating the Effects of PA66 Electrospun Nanofibers Layered within an Adhesive Composite Joint Fabricated under Autoclave Curing}, author = {Gözde Esenoğlu and Metin Tanoğlu and Murat Barisik and Hande İplikçi and Melisa Yeke and Kaan Nuhoğlu and Ceren Türkdoğan and Seçkin Martin and Engin Aktaş and Serkan Dehneliler and Ahmet Ayberk Gürbüz and Mehmet Erdem İriş}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85172448706&doi=10.1021%2facsomega.3c03419&partnerID=40&md5=7f3ddea2390eb013c802b710a5aaf695}, doi = {10.1021/acsomega.3c03419}, year = {2023}, date = {2023-01-01}, journal = {ACS Omega}, volume = {8}, number = {36}, pages = {32656 – 32666}, abstract = {Enhancing the performance of adhesively joined composite components is crucial for various industrial applications. In this study, polyamide 66 (PA66) nanofibers produced by electrospinning were coated on unidirectional carbon/epoxy prepregs to increase the bond strength of the composites. Carbon/epoxy prepregs with/without PA66 nanofiber coating on the bonding region were fabricated using the autoclave, which is often used in the aerospace industry. The single lap shear Charpy impact energy and Mode-I fracture toughness tests were employed to examine the effects of PA66 nanofibers on the mechanical properties of the joint region. Scanning electron microscopy (SEM) was used to investigate the nanofiber morphology and fracture modes. The thermal characteristics of Polyamide 66 nanofibers were explored by using differential scanning calorimetry (DSC). We observed that the electrospun PA66 nanofiber coating on the prepreg surfaces substantially improves the joint strength. Results revealed that the single lap shear and Charpy impact strength values of the composite joint are increased by about 79 and 24%, respectively, by coating PA66 nanofibers onto the joining region. The results also showed that by coating PA66 nanofibers, the Mode-I fracture toughness value was improved by about 107% while the glass transition temperature remained constant. © 2023 The Authors. Published by American Chemical Society.}, note = {All Open Access, Gold Open Access, Green Open Access}, keywords = {}, pubstate = {published}, tppubtype = {article} } Enhancing the performance of adhesively joined composite components is crucial for various industrial applications. In this study, polyamide 66 (PA66) nanofibers produced by electrospinning were coated on unidirectional carbon/epoxy prepregs to increase the bond strength of the composites. Carbon/epoxy prepregs with/without PA66 nanofiber coating on the bonding region were fabricated using the autoclave, which is often used in the aerospace industry. The single lap shear Charpy impact energy and Mode-I fracture toughness tests were employed to examine the effects of PA66 nanofibers on the mechanical properties of the joint region. Scanning electron microscopy (SEM) was used to investigate the nanofiber morphology and fracture modes. The thermal characteristics of Polyamide 66 nanofibers were explored by using differential scanning calorimetry (DSC). We observed that the electrospun PA66 nanofiber coating on the prepreg surfaces substantially improves the joint strength. Results revealed that the single lap shear and Charpy impact strength values of the composite joint are increased by about 79 and 24%, respectively, by coating PA66 nanofibers onto the joining region. The results also showed that by coating PA66 nanofibers, the Mode-I fracture toughness value was improved by about 107% while the glass transition temperature remained constant. © 2023 The Authors. Published by American Chemical Society. |
Kandemir, Sinan; Bohlen, Jan; Dieringa, Hajo Influence of recycled carbon fiber addition on the microstructure and creep response of extruded AZ91 magnesium alloy Journal Article Journal of Magnesium and Alloys, 11 (7), pp. 2518 – 2529, 2023, (All Open Access, Gold Open Access). @article{Kandemir20232518, title = {Influence of recycled carbon fiber addition on the microstructure and creep response of extruded AZ91 magnesium alloy}, author = {Sinan Kandemir and Jan Bohlen and Hajo Dieringa}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85166356480&doi=10.1016%2fj.jma.2023.06.004&partnerID=40&md5=c08bdbb377339cd4ef3e7fcae68561d5}, doi = {10.1016/j.jma.2023.06.004}, year = {2023}, date = {2023-01-01}, journal = {Journal of Magnesium and Alloys}, volume = {11}, number = {7}, pages = {2518 – 2529}, abstract = {In this study, the recycled short carbon fiber (CF)-reinforced magnesium matrix composites were fabricated using a combination of stir casting and hot extrusion. The objective was to investigate the impact of CF content (2.5 and 5.0 wt.%) and fiber length (100 and 500 µm) on the microstructure, mechanical properties, and creep behavior of AZ91 alloy matrix. The microstructural analysis revealed that the CFs aligned in the extrusion direction resulted in grain and intermetallic refinement within the alloy. In comparison to the unreinforced AZ91 alloy, the composites with 2.5 wt.% CF exhibited an increase in hardness by 16–20% and yield strength by 5–15%, depending on the fiber length, while experiencing a reduction in ductility. When the reinforcement content was increased from 2.5 to 5.0 wt.%, strength values exhibited fluctuations and decline, accompanied by decreased ductility. These divergent outcomes were discussed in relation to fiber length, clustering tendency due to higher reinforcement content, and the presence of interfacial products with micro-cracks at the CF-matrix interface. Tensile creep tests indicated that CFs did not enhance the creep resistance of extruded AZ91 alloy, suggesting that grain boundary sliding is likely the dominant deformation mechanism during creep. © 2023}, note = {All Open Access, Gold Open Access}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, the recycled short carbon fiber (CF)-reinforced magnesium matrix composites were fabricated using a combination of stir casting and hot extrusion. The objective was to investigate the impact of CF content (2.5 and 5.0 wt.%) and fiber length (100 and 500 µm) on the microstructure, mechanical properties, and creep behavior of AZ91 alloy matrix. The microstructural analysis revealed that the CFs aligned in the extrusion direction resulted in grain and intermetallic refinement within the alloy. In comparison to the unreinforced AZ91 alloy, the composites with 2.5 wt.% CF exhibited an increase in hardness by 16–20% and yield strength by 5–15%, depending on the fiber length, while experiencing a reduction in ductility. When the reinforcement content was increased from 2.5 to 5.0 wt.%, strength values exhibited fluctuations and decline, accompanied by decreased ductility. These divergent outcomes were discussed in relation to fiber length, clustering tendency due to higher reinforcement content, and the presence of interfacial products with micro-cracks at the CF-matrix interface. Tensile creep tests indicated that CFs did not enhance the creep resistance of extruded AZ91 alloy, suggesting that grain boundary sliding is likely the dominant deformation mechanism during creep. © 2023 |
Uz, Yusuf Can; Tanoğlu, Metin Determination of activation energy for carbon/epoxy prepregs containing carbon nanotubes by differential scanning calorimetry Journal Article High Performance Polymers, 35 (2), pp. 166 – 180, 2023. @article{Uz2023166, title = {Determination of activation energy for carbon/epoxy prepregs containing carbon nanotubes by differential scanning calorimetry}, author = {Yusuf Can Uz and Metin Tanoğlu}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85135891731&doi=10.1177%2f09540083221115987&partnerID=40&md5=4b3d7c567d57a6b645d854737e03917d}, doi = {10.1177/09540083221115987}, year = {2023}, date = {2023-01-01}, journal = {High Performance Polymers}, volume = {35}, number = {2}, pages = {166 – 180}, abstract = {The aim of the present study is the thermal characterization of laboratory-scale carbon fiber/epoxy-based prepregs by incorporating single-wall carbon nanotubes (SWCNTs). Investigation of the cure behavior of a prepreg system is crucial for the characterization and optimization of the fiber reinforced polymeric (FRP) composite. To affect dispersion characteristics, SWCNTs were functionalized by oxidizing their surface with carboxyl (-COOH) group using an acid treatment. The modified resin system contained 0.05, 0.1, and 0.2 wt. % functionalized SWCNTs (F-SWCNTs). Carbon fiber (CF) reinforced prepregs containing various amount of F-SWCNTs were prepared using drum-type winding technique. FTIR was performed to identify new bonding groups formed after the functionalization of SWCNTs. Cure kinetics of prepregs prepared with/without F-SWCNTs were investigated using isoconversional methods. © The Author(s) 2022.}, keywords = {}, pubstate = {published}, tppubtype = {article} } The aim of the present study is the thermal characterization of laboratory-scale carbon fiber/epoxy-based prepregs by incorporating single-wall carbon nanotubes (SWCNTs). Investigation of the cure behavior of a prepreg system is crucial for the characterization and optimization of the fiber reinforced polymeric (FRP) composite. To affect dispersion characteristics, SWCNTs were functionalized by oxidizing their surface with carboxyl (-COOH) group using an acid treatment. The modified resin system contained 0.05, 0.1, and 0.2 wt. % functionalized SWCNTs (F-SWCNTs). Carbon fiber (CF) reinforced prepregs containing various amount of F-SWCNTs were prepared using drum-type winding technique. FTIR was performed to identify new bonding groups formed after the functionalization of SWCNTs. Cure kinetics of prepregs prepared with/without F-SWCNTs were investigated using isoconversional methods. © The Author(s) 2022. |
2022 |
Esenoğlu, G; Barisik, M; Tanoğlu, M; Yeke, M; Türkdoğan, C; İplikçi, H; Martin, S; Nuhoğlu, K; Aktaş, E; Dehneliler, S; İriş, M E Improving adhesive behavior of fiber reinforced composites by incorporating electrospun Polyamide-6,6 nanofibers in joining region Journal Article Journal of Composite Materials, 56 (29), pp. 4449-4459, 2022. @article{Esenoğlu20224449, title = {Improving adhesive behavior of fiber reinforced composites by incorporating electrospun Polyamide-6,6 nanofibers in joining region}, author = {G Esenoğlu and M Barisik and M Tanoğlu and M Yeke and C Türkdoğan and H İplikçi and S Martin and K Nuhoğlu and E Aktaş and S Dehneliler and M E İriş}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85139985112&doi=10.1177%2f00219983221133478&partnerID=40&md5=699a47f9c6bc7948245cdc6f370c483e}, doi = {10.1177/00219983221133478}, year = {2022}, date = {2022-01-01}, journal = {Journal of Composite Materials}, volume = {56}, number = {29}, pages = {4449-4459}, abstract = {Adhesive joining of fiber reinforced polymer (CFRP) composite components is demanded in various industrial applications. However, the joining locations frequently suffer from adhesive bond failure between adhesive and adherent. The aim of the present study is improving bonding behavior of adhesive joints by electrospun nanofiber coatings on the prepreg surfaces that have been used for composite manufacturing. Secondary bonding of woven and unidirectional CFRP parts was selected since this configuration is preferred commonly in aerospace practices. The optimum nanofiber coating with a low average fiber diameter and areal weight density is succeed by studying various solution concentrations and spinning durations of the polyamide-6.6 (PA 66) electrospinning. We obtained homogeneous and beadles nanofiber productions. As a result, an average diameter of 36.50 ± 12 nm electrospun nanofibers were obtained and coated onto the prepreg surfaces. Prepreg systems with/without PA 66 nanofibers were hot pressed to fabricate the CFRP composite laminates. The single-lap shear test coupons were prepared from the fabricated laminates to examine the effects of PA 66 nanofibers on the mechanical properties of the joint region of the composites. The single-lap shear test results showed that the bonding strength is improved by about 40% with minimal adhesive use due to the presence of the electrospun nanofibers within the joint region. The optical and SEM images of fractured surfaces showed that nanofiber-coated joints exhibited a coherent failure while the bare surfaces underwent adhesive failure. The PA66 nanofibers created better coupling between the adhesive and the composite surface by increasing the surface area and roughness. As a result, electrospun nanofibers turned adhesive failure into cohesive and enhanced the adhesion performance composite joints substantially. © The Author(s) 2022.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Adhesive joining of fiber reinforced polymer (CFRP) composite components is demanded in various industrial applications. However, the joining locations frequently suffer from adhesive bond failure between adhesive and adherent. The aim of the present study is improving bonding behavior of adhesive joints by electrospun nanofiber coatings on the prepreg surfaces that have been used for composite manufacturing. Secondary bonding of woven and unidirectional CFRP parts was selected since this configuration is preferred commonly in aerospace practices. The optimum nanofiber coating with a low average fiber diameter and areal weight density is succeed by studying various solution concentrations and spinning durations of the polyamide-6.6 (PA 66) electrospinning. We obtained homogeneous and beadles nanofiber productions. As a result, an average diameter of 36.50 ± 12 nm electrospun nanofibers were obtained and coated onto the prepreg surfaces. Prepreg systems with/without PA 66 nanofibers were hot pressed to fabricate the CFRP composite laminates. The single-lap shear test coupons were prepared from the fabricated laminates to examine the effects of PA 66 nanofibers on the mechanical properties of the joint region of the composites. The single-lap shear test results showed that the bonding strength is improved by about 40% with minimal adhesive use due to the presence of the electrospun nanofibers within the joint region. The optical and SEM images of fractured surfaces showed that nanofiber-coated joints exhibited a coherent failure while the bare surfaces underwent adhesive failure. The PA66 nanofibers created better coupling between the adhesive and the composite surface by increasing the surface area and roughness. As a result, electrospun nanofibers turned adhesive failure into cohesive and enhanced the adhesion performance composite joints substantially. © The Author(s) 2022. |
Güneş, M D; Karabaş, İmamoğlu N; Deveci, H A; Tanoğlu, G; Tanoğlu, M Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 236 (19), pp. 10290-10303, 2022. @article{Güneş202210290, title = {Fatigue life prediction and optimization of GFRP composites based on Failure Tensor Polynomial in Fatigue model with exponential fitting approach}, author = {M D Güneş and N İmamoğlu Karabaş and H A Deveci and G Tanoğlu and M Tanoğlu}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85130983288&doi=10.1177%2f09544062221101462&partnerID=40&md5=144a189eaf81ed03065a753253307cad}, doi = {10.1177/09544062221101462}, year = {2022}, date = {2022-01-01}, journal = {Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science}, volume = {236}, number = {19}, pages = {10290-10303}, abstract = {In this study, a new fatigue life prediction and optimization strategy utilizing the Failure Tensor Polynomial in Fatigue (FTPF) model with exponential fitting and numerical bisection method for fiber reinforced polymer composites has been proposed. Within the experimental stage, glass/epoxy composite laminates with (Formula presented.), (Formula presented.), and (Formula presented.) lay-up configurations were fabricated, quasi-static and fatigue mechanical behavior of GFRP composites was characterized to be used in the FTPF model. The prediction capability of the FTPF model was tested based on the experimental data obtained for multidirectional laminates of various composite materials. Fatigue life prediction results of the glass/epoxy laminates were found to be better as compared to those for the linear fitting predictions. The results also indicated that the approach with exponential fitting provides better fatigue life predictions as compared to those obtained by linear fitting, especially for glass/epoxy laminates. Moreover, an optimization study using the proposed methodology for fatigue life advancement of the glass/epoxy laminates was performed by a powerful hybrid algorithm, PSA/GPSA. So, two optimization scenarios including various loading configurations were considered. The optimization results exhibited that the optimized stacking sequences having maximized fatigue life can be obtained in various loading cases. It was also revealed that the tension-compression loading and the loadings involving shear loads are critical for fatigue, and further improvement in fatigue life may be achieved by designing only symmetric lay-ups instead of symmetric-balanced and diversification of fiber angles to be used in the optimization. © IMechE 2022.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, a new fatigue life prediction and optimization strategy utilizing the Failure Tensor Polynomial in Fatigue (FTPF) model with exponential fitting and numerical bisection method for fiber reinforced polymer composites has been proposed. Within the experimental stage, glass/epoxy composite laminates with (Formula presented.), (Formula presented.), and (Formula presented.) lay-up configurations were fabricated, quasi-static and fatigue mechanical behavior of GFRP composites was characterized to be used in the FTPF model. The prediction capability of the FTPF model was tested based on the experimental data obtained for multidirectional laminates of various composite materials. Fatigue life prediction results of the glass/epoxy laminates were found to be better as compared to those for the linear fitting predictions. The results also indicated that the approach with exponential fitting provides better fatigue life predictions as compared to those obtained by linear fitting, especially for glass/epoxy laminates. Moreover, an optimization study using the proposed methodology for fatigue life advancement of the glass/epoxy laminates was performed by a powerful hybrid algorithm, PSA/GPSA. So, two optimization scenarios including various loading configurations were considered. The optimization results exhibited that the optimized stacking sequences having maximized fatigue life can be obtained in various loading cases. It was also revealed that the tension-compression loading and the loadings involving shear loads are critical for fatigue, and further improvement in fatigue life may be achieved by designing only symmetric lay-ups instead of symmetric-balanced and diversification of fiber angles to be used in the optimization. © IMechE 2022. |
Üstün, Sinan H; Toksoy, Kaan A; Tanoğlu, M Investigation of hybridization effect on ballistic performance of multi-layered fiber reinforced composite structures Journal Article Journal of Composite Materials, 56 (15), pp. 2411-2431, 2022. @article{SinanÜstün20222411, title = {Investigation of hybridization effect on ballistic performance of multi-layered fiber reinforced composite structures}, author = {H Sinan Üstün and A Kaan Toksoy and M Tanoğlu}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85130035790&doi=10.1177%2f00219983221090018&partnerID=40&md5=c04588512f22392bf8cac3ef9d118408}, doi = {10.1177/00219983221090018}, year = {2022}, date = {2022-01-01}, journal = {Journal of Composite Materials}, volume = {56}, number = {15}, pages = {2411-2431}, abstract = {The aim of this study is enhancing the ballistic performance of multi-layered fiber reinforced composite structures by hybridization approach against fragment simulating projectile (FSP). For manufacturing of homogeneous and hybrid composite structures, 170 g/m2 twill weave aramid and 280 g/m2 plain weave E-Glass fibers were used with epoxy resin systems and two different thickness values for each composite panel were fabricated and tested to obtain a relationship between areal density and V50 parameters. Tensile, 3-point bending, and short beam strength tests of composite panels were performed, and ballistic performance of composite structures were measured by V50 test method with 1.1 g FSP threat. Ballistic performance of hybrid composite structures was compared with high-performance composite ballistic panel test results reported in literature. As a result, it was found that E-Glass fabric layers together with aramid fabrics increased the energy absorbing capability of hybrid composite panels and ballistic performance was enhanced to be similar or higher than ballistic fiber reinforced composites. Hence, hybridization was found to be an effective way to enhance ballistic performance of fiber reinforced composite structures. © The Author(s) 2022.}, keywords = {}, pubstate = {published}, tppubtype = {article} } The aim of this study is enhancing the ballistic performance of multi-layered fiber reinforced composite structures by hybridization approach against fragment simulating projectile (FSP). For manufacturing of homogeneous and hybrid composite structures, 170 g/m2 twill weave aramid and 280 g/m2 plain weave E-Glass fibers were used with epoxy resin systems and two different thickness values for each composite panel were fabricated and tested to obtain a relationship between areal density and V50 parameters. Tensile, 3-point bending, and short beam strength tests of composite panels were performed, and ballistic performance of composite structures were measured by V50 test method with 1.1 g FSP threat. Ballistic performance of hybrid composite structures was compared with high-performance composite ballistic panel test results reported in literature. As a result, it was found that E-Glass fabric layers together with aramid fabrics increased the energy absorbing capability of hybrid composite panels and ballistic performance was enhanced to be similar or higher than ballistic fiber reinforced composites. Hence, hybridization was found to be an effective way to enhance ballistic performance of fiber reinforced composite structures. © The Author(s) 2022. |
Uz, Y C; Tanoğlu, M Determination of activation energy for carbon/epoxy prepregs containing carbon nanotubes by differential scanning calorimetry Journal Article High Performance Polymers, 2022. @article{Uz2022, title = {Determination of activation energy for carbon/epoxy prepregs containing carbon nanotubes by differential scanning calorimetry}, author = {Y C Uz and M Tanoğlu}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85135891731&doi=10.1177%2f09540083221115987&partnerID=40&md5=4b3d7c567d57a6b645d854737e03917d}, doi = {10.1177/09540083221115987}, year = {2022}, date = {2022-01-01}, journal = {High Performance Polymers}, abstract = {The aim of the present study is the thermal characterization of laboratory-scale carbon fiber/epoxy-based prepregs by incorporating single-wall carbon nanotubes (SWCNTs). Investigation of the cure behavior of a prepreg system is crucial for the characterization and optimization of the fiber reinforced polymeric (FRP) composite. To affect dispersion characteristics, SWCNTs were functionalized by oxidizing their surface with carboxyl (-COOH) group using an acid treatment. The modified resin system contained 0.05, 0.1, and 0.2 wt. % functionalized SWCNTs (F-SWCNTs). Carbon fiber (CF) reinforced prepregs containing various amount of F-SWCNTs were prepared using drum-type winding technique. FTIR was performed to identify new bonding groups formed after the functionalization of SWCNTs. Cure kinetics of prepregs prepared with/without F-SWCNTs were investigated using isoconversional methods. © The Author(s) 2022.}, keywords = {}, pubstate = {published}, tppubtype = {article} } The aim of the present study is the thermal characterization of laboratory-scale carbon fiber/epoxy-based prepregs by incorporating single-wall carbon nanotubes (SWCNTs). Investigation of the cure behavior of a prepreg system is crucial for the characterization and optimization of the fiber reinforced polymeric (FRP) composite. To affect dispersion characteristics, SWCNTs were functionalized by oxidizing their surface with carboxyl (-COOH) group using an acid treatment. The modified resin system contained 0.05, 0.1, and 0.2 wt. % functionalized SWCNTs (F-SWCNTs). Carbon fiber (CF) reinforced prepregs containing various amount of F-SWCNTs were prepared using drum-type winding technique. FTIR was performed to identify new bonding groups formed after the functionalization of SWCNTs. Cure kinetics of prepregs prepared with/without F-SWCNTs were investigated using isoconversional methods. © The Author(s) 2022. |
Solak, Ay Z; Kartav, O; Tanoglu, M Enhancement of filament wound glass fiber/epoxy-based cylindrical composites by toughening with single-walled carbon nanotubes Journal Article Polymers and Polymer Composites, 30 , 2022. @article{AySolak2022, title = {Enhancement of filament wound glass fiber/epoxy-based cylindrical composites by toughening with single-walled carbon nanotubes}, author = {Z Ay Solak and O Kartav and M Tanoglu}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85131795670&doi=10.1177%2f09673911221086718&partnerID=40&md5=ee2274734defe29b42d80148622b6359}, doi = {10.1177/09673911221086718}, year = {2022}, date = {2022-01-01}, journal = {Polymers and Polymer Composites}, volume = {30}, abstract = {In this study, the effect of incorporating nano-sized fillers (noncovalently functionalized with ethoxylated alcohol chemical-vapor-deposition-grown SWCNTs) within an epoxy resin on the performance of filament wound glass fiber (GF)-based cylindrical composites (GFCCs) was investigated. For this purpose, SWCNTs were dispersed with the concentration of 0.05 and 0.1 weight percent (wt.%) within an epoxy resin using mechanical stirring and calendaring (3-roll-milling) techniques. The rheological behavior of the SWCNT incorporated epoxy mixture was characterized to determine the suitability of blends for the filament winding process. It was revealed that the viscosity value of the resin was not significantly affected by the addition of SWCNTs in given concentrations. Moreover, contact angle measurements were also performed on the SWCNT/epoxy blends dropped on the GF for the evaluation of the wettability behavior of the GF in the presence of the SWCNTs in relevant concentrations. Eventually, it was observed that the wettability behavior of GF was not reasonably affected by the presence of the SWCNTs. The double cantilever beam (DCB), flexural, and short beam shear (SBS) tests were performed on the reference and SWCNT-modified GFCC specimens to evaluate the effects of the SWCNT presence on the interlaminar fracture toughness and out-of-plane properties of GFCCs. The fractured surfaces after the DCB and SBS tests were analyzed under the scanning electron microscopy to reveal the toughening mechanisms and the filler morphologies. Consequently, although SWCNT incorporation was on the outermost layer of GFCCs, it was found that the interlaminar shear strength (ILSS) values and Mode I interlaminar fracture toughness values of the curved composite samples were improved up to 22 and 216%, respectively, due to the presence of the SWCNTs. © The Author(s) 2022.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, the effect of incorporating nano-sized fillers (noncovalently functionalized with ethoxylated alcohol chemical-vapor-deposition-grown SWCNTs) within an epoxy resin on the performance of filament wound glass fiber (GF)-based cylindrical composites (GFCCs) was investigated. For this purpose, SWCNTs were dispersed with the concentration of 0.05 and 0.1 weight percent (wt.%) within an epoxy resin using mechanical stirring and calendaring (3-roll-milling) techniques. The rheological behavior of the SWCNT incorporated epoxy mixture was characterized to determine the suitability of blends for the filament winding process. It was revealed that the viscosity value of the resin was not significantly affected by the addition of SWCNTs in given concentrations. Moreover, contact angle measurements were also performed on the SWCNT/epoxy blends dropped on the GF for the evaluation of the wettability behavior of the GF in the presence of the SWCNTs in relevant concentrations. Eventually, it was observed that the wettability behavior of GF was not reasonably affected by the presence of the SWCNTs. The double cantilever beam (DCB), flexural, and short beam shear (SBS) tests were performed on the reference and SWCNT-modified GFCC specimens to evaluate the effects of the SWCNT presence on the interlaminar fracture toughness and out-of-plane properties of GFCCs. The fractured surfaces after the DCB and SBS tests were analyzed under the scanning electron microscopy to reveal the toughening mechanisms and the filler morphologies. Consequently, although SWCNT incorporation was on the outermost layer of GFCCs, it was found that the interlaminar shear strength (ILSS) values and Mode I interlaminar fracture toughness values of the curved composite samples were improved up to 22 and 216%, respectively, due to the presence of the SWCNTs. © The Author(s) 2022. |
2021 |
Kangal, Serkan; Say, Harun A; Ayakda, Ozan; Kartav, Osman; Aydin, Levent; Artem, Secil H; Aktas, Engin; Yuceturk, Kutay; Tanoglu, Metin; Kandemir, Sinan; Beylergil, Bertan A Comprehensive Study on Burst Pressure Performance of Aluminum Liner for Hydrogen Storage Vessels Journal Article JOURNAL OF PRESSURE VESSEL TECHNOLOGY-TRANSACTIONS OF THE ASME, 143 (4), 2021. @article{WOS:000669955100012, title = {A Comprehensive Study on Burst Pressure Performance of Aluminum Liner for Hydrogen Storage Vessels}, author = {Serkan Kangal and Harun A Say and Ozan Ayakda and Osman Kartav and Levent Aydin and Secil H Artem and Engin Aktas and Kutay Yuceturk and Metin Tanoglu and Sinan Kandemir and Bertan Beylergil}, doi = {10.1115/1.4049644}, year = {2021}, date = {2021-08-01}, journal = {JOURNAL OF PRESSURE VESSEL TECHNOLOGY-TRANSACTIONS OF THE ASME}, volume = {143}, number = {4}, abstract = {This paper presents a comparative study on the burst pressure performance of aluminum (Al) liner for type-III composite overwrapped pressure vessels (COPVs). In the analysis, the vessels were loaded with increasing internal pressure up to the burst pressure level. In the analytical part of the study, the burst pressure of the cylindrical part was predicted based on the modified von Mises, Tresca, and average shear stress criterion (ASSC). In the numerical analysis, a finite element (FE) model was established in order to predict the behavior of the vessel as a function of increasing internal pressure and determine the final burst. The Al pressure vessels made of Al-6061-T6 alloy with a capacity of 5 L were designed. The manufacturing of the metallic vessels was purchased from a metal forming company. The experimental study was conducted by pressurizing the Al vessels until the burst failure occurred. The radial and axial strain behaviors were monitored at various locations on the vessels during loading. The results obtained through analytical, numerical, and experimental work were compared. The average experimental burst pressure of the vessels was found to be 279 bar. The experimental strain data were compared with the results of the FE analysis. The results indicated that the FE analysis and ASSC-based elastoplastic analytical approaches yielded the best predictions which are within 2.2% of the experimental burst failure values. It was also found that the elastic analysis underestimated the burst failure results; however, it was effective for determining the critical regions over the vessel structure. The strain behavior of the vessels obtained through experimental investigations was well correlated with those predicted through FE analysis.}, keywords = {}, pubstate = {published}, tppubtype = {article} } This paper presents a comparative study on the burst pressure performance of aluminum (Al) liner for type-III composite overwrapped pressure vessels (COPVs). In the analysis, the vessels were loaded with increasing internal pressure up to the burst pressure level. In the analytical part of the study, the burst pressure of the cylindrical part was predicted based on the modified von Mises, Tresca, and average shear stress criterion (ASSC). In the numerical analysis, a finite element (FE) model was established in order to predict the behavior of the vessel as a function of increasing internal pressure and determine the final burst. The Al pressure vessels made of Al-6061-T6 alloy with a capacity of 5 L were designed. The manufacturing of the metallic vessels was purchased from a metal forming company. The experimental study was conducted by pressurizing the Al vessels until the burst failure occurred. The radial and axial strain behaviors were monitored at various locations on the vessels during loading. The results obtained through analytical, numerical, and experimental work were compared. The average experimental burst pressure of the vessels was found to be 279 bar. The experimental strain data were compared with the results of the FE analysis. The results indicated that the FE analysis and ASSC-based elastoplastic analytical approaches yielded the best predictions which are within 2.2% of the experimental burst failure values. It was also found that the elastic analysis underestimated the burst failure results; however, it was effective for determining the critical regions over the vessel structure. The strain behavior of the vessels obtained through experimental investigations was well correlated with those predicted through FE analysis. |
Kandemir, S; Gavras, S; Dieringa, H Journal of Magnesium and Alloys, 9 (5), pp. 1753-1767, 2021. @article{Kandemir20211753, title = {High temperature tensile, compression and creep behavior of recycled short carbon fibre reinforced AZ91 magnesium alloy fabricated by a high shearing dispersion technique}, author = {S Kandemir and S Gavras and H Dieringa}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85106274015&doi=10.1016%2fj.jma.2021.03.029&partnerID=40&md5=33482583e6489310dc991aed7c7b0793}, doi = {10.1016/j.jma.2021.03.029}, year = {2021}, date = {2021-01-01}, journal = {Journal of Magnesium and Alloys}, volume = {9}, number = {5}, pages = {1753-1767}, abstract = {The present study seeks the feasibility of using short carbon fibres recycled from polymer matrix composites as alternative to virgin carbon fibres in the reinforcement of magnesium alloys. The microstructures, high temperature mechanical and creep properties of AZ91 alloy and its composites with various recycled carbon fibre contents (2.5 and 5 wt.%) and lengths (100 and 500 μm) were investigated in the temperature range of 25–200 °C. The microstructural characterization showed that the high shear dispersion technique provided the cast composites with finer grains and relatively homogenous distribution of fibres. The materials tested displayed different behaviour depending on the type of loading. In general, while enhancements in the mechanical properties of composites is attributed to the load bearing and grain refinement effects of fibres, the fluctuations in the properties were discussed on the basis of porosity formation, relatively high reinforcement content leading to fibre clustering and interlayer found between the matrix and reinforcement compared to those of AZ91 alloy. The compressive creep tests revealed similar or higher minimum creep rates in the recycled carbon fibre reinforced AZ91 in comparison to the unreinforced AZ91. © 2021}, keywords = {}, pubstate = {published}, tppubtype = {article} } The present study seeks the feasibility of using short carbon fibres recycled from polymer matrix composites as alternative to virgin carbon fibres in the reinforcement of magnesium alloys. The microstructures, high temperature mechanical and creep properties of AZ91 alloy and its composites with various recycled carbon fibre contents (2.5 and 5 wt.%) and lengths (100 and 500 μm) were investigated in the temperature range of 25–200 °C. The microstructural characterization showed that the high shear dispersion technique provided the cast composites with finer grains and relatively homogenous distribution of fibres. The materials tested displayed different behaviour depending on the type of loading. In general, while enhancements in the mechanical properties of composites is attributed to the load bearing and grain refinement effects of fibres, the fluctuations in the properties were discussed on the basis of porosity formation, relatively high reinforcement content leading to fibre clustering and interlayer found between the matrix and reinforcement compared to those of AZ91 alloy. The compressive creep tests revealed similar or higher minimum creep rates in the recycled carbon fibre reinforced AZ91 in comparison to the unreinforced AZ91. © 2021 |
Martin, S; Kandemir, S; Antonov, M Investigation of the high temperature dry sliding wear behavior of graphene nanoplatelets reinforced aluminum matrix composites Journal Article Journal of Composite Materials, 55 (13), pp. 1769-1782, 2021. @article{Martin20211769, title = {Investigation of the high temperature dry sliding wear behavior of graphene nanoplatelets reinforced aluminum matrix composites}, author = {S Martin and S Kandemir and M Antonov}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85097279024&doi=10.1177%2f0021998320979037&partnerID=40&md5=554c5ed3fcc37de88e360d033402ed4b}, doi = {10.1177/0021998320979037}, year = {2021}, date = {2021-01-01}, journal = {Journal of Composite Materials}, volume = {55}, number = {13}, pages = {1769-1782}, abstract = {In this study, graphene nanoplatelets (GNPs) with a thickness of 50-100 nm have been utilized to improve the mechanical and tribological properties of A360 alloy due to their extraordinary mechanical properties and solid lubricant nature. For the investigation of tribological properties, ball-on disc tests were carried out at various temperatures including room temperature (RT), 150 °C, and 300 °C. According to the hardness and ball-on-disc test results, the nanocomposite samples reinforced with GNPs exhibited improved hardness and wear resistance. The improvement in the wear behavior of nanocomposites was referred to the temporarily formed solid lubricant film of harder GNPs during the wear, and hence coefficient of friction (COF) and volume loss were considerably reduced. Abrasive-adhesive, oxidative, and mild-to-severe were found to be main wear mechanisms at RT, 150 °C, and 300 °C, respectively. Overall, the results show that the nanocomposites fabricated by casting method combined with mechanical stirring and ultrasonication have promising wear performance, especially at elevated temperatures. This may suggest that these developed materials could be potential candidates to be used in the engineering applications requiring high temperature wear performance. © The Author(s) 2020.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, graphene nanoplatelets (GNPs) with a thickness of 50-100 nm have been utilized to improve the mechanical and tribological properties of A360 alloy due to their extraordinary mechanical properties and solid lubricant nature. For the investigation of tribological properties, ball-on disc tests were carried out at various temperatures including room temperature (RT), 150 °C, and 300 °C. According to the hardness and ball-on-disc test results, the nanocomposite samples reinforced with GNPs exhibited improved hardness and wear resistance. The improvement in the wear behavior of nanocomposites was referred to the temporarily formed solid lubricant film of harder GNPs during the wear, and hence coefficient of friction (COF) and volume loss were considerably reduced. Abrasive-adhesive, oxidative, and mild-to-severe were found to be main wear mechanisms at RT, 150 °C, and 300 °C, respectively. Overall, the results show that the nanocomposites fabricated by casting method combined with mechanical stirring and ultrasonication have promising wear performance, especially at elevated temperatures. This may suggest that these developed materials could be potential candidates to be used in the engineering applications requiring high temperature wear performance. © The Author(s) 2020. |
Kartav, O; Kangal, S; Yücetürk, K; Tanoğlu, M; Aktaş, E; Artem, H S Development and analysis of composite overwrapped pressure vessels for hydrogen storage Journal Article Journal of Composite Materials, 55 (28), pp. 4141-4155, 2021. @article{Kartav20214141, title = {Development and analysis of composite overwrapped pressure vessels for hydrogen storage}, author = {O Kartav and S Kangal and K Yücetürk and M Tanoğlu and E Aktaş and H S Artem}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85110939454&doi=10.1177%2f00219983211033568&partnerID=40&md5=c31db8e0f0de63135bf2da9bf634900d}, doi = {10.1177/00219983211033568}, year = {2021}, date = {2021-01-01}, journal = {Journal of Composite Materials}, volume = {55}, number = {28}, pages = {4141-4155}, abstract = {In this study, composite overwrapped pressure vessels (COPVs) for high-pressure hydrogen storage were designed, modeled by finite element (FE) method, manufactured by filament winding technique and tested for burst pressure. Aluminum 6061-T6 was selected as a metallic liner material. Epoxy impregnated carbon filaments were overwrapped over the liner with a winding angle of ±14° to obtain fully overwrapped composite reinforced vessels with non-identical front and back dome layers. The COPVs were loaded with increasing internal pressure up to the burst pressure level. During loading, deformation of the vessels was measured locally with strain gauges. The mechanical performances of COPVs designed with various number of helical, hoop and doily layers were investigated by both experimental and numerical methods. In numerical method, FE analysis containing a simple progressive damage model available in ANSYS software package for the composite section was performed. The results revealed that the FE model provides a good correlation as compared to experimental strain results for the developed COPVs. The burst pressure test results showed that integration of doily layers to the filament winding process resulted with an improvement of the COPVs performance. © The Author(s) 2021.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, composite overwrapped pressure vessels (COPVs) for high-pressure hydrogen storage were designed, modeled by finite element (FE) method, manufactured by filament winding technique and tested for burst pressure. Aluminum 6061-T6 was selected as a metallic liner material. Epoxy impregnated carbon filaments were overwrapped over the liner with a winding angle of ±14° to obtain fully overwrapped composite reinforced vessels with non-identical front and back dome layers. The COPVs were loaded with increasing internal pressure up to the burst pressure level. During loading, deformation of the vessels was measured locally with strain gauges. The mechanical performances of COPVs designed with various number of helical, hoop and doily layers were investigated by both experimental and numerical methods. In numerical method, FE analysis containing a simple progressive damage model available in ANSYS software package for the composite section was performed. The results revealed that the FE model provides a good correlation as compared to experimental strain results for the developed COPVs. The burst pressure test results showed that integration of doily layers to the filament winding process resulted with an improvement of the COPVs performance. © The Author(s) 2021. |
2020 |
Beylergil, Bertan; Tanoglu, Metin; Aktas, Engin Experimental and statistical analysis of carbon fiber/epoxy composites interleaved with nylon 6,6 nonwoven fabric interlayers Journal Article JOURNAL OF COMPOSITE MATERIALS, 54 (27), pp. 4173-4184, 2020, ISSN: 0021-9983. @article{ISI:000535519800001, title = {Experimental and statistical analysis of carbon fiber/epoxy composites interleaved with nylon 6,6 nonwoven fabric interlayers}, author = {Bertan Beylergil and Metin Tanoglu and Engin Aktas}, doi = {10.1177/0021998320927740, Early Access Date = MAY 2020}, issn = {0021-9983}, year = {2020}, date = {2020-11-01}, journal = {JOURNAL OF COMPOSITE MATERIALS}, volume = {54}, number = {27}, pages = {4173-4184}, abstract = {Thermoplastic interleaving is a promising technique to improve delamination resistance of laminated composites. In this study, plain-weave carbon fiber/epoxy composites were interleaved with nylon 6,6 nonwoven fabrics with an areal weight density of 17 gsm. The carbon fiber/epoxy composite laminates with/without nylon 6,6 nonwoven fabric interlayers were manufactured by VARTM technique. Double cantilever beam fracture toughness tests were carried out on the prepared composite test specimens in accordance with ASTM 5528 standard. The experimental test data were statistically analyzed by two-parameter Weibull distribution. The results showed that the initiation and propagation fracture toughness Mode-I fracture toughness of carbon fiber/epoxy composites could be improved by about 34 and 156% (corresponding to a reliability level of 0.50) with the incorporation of nylon 6,6 interlayers in the interlaminar region, respectively. The results also revealed that the percent increase in the propagation fracture toughness value was 67 and 41% at reliability levels of 0.90 and 0.95, respectively.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Thermoplastic interleaving is a promising technique to improve delamination resistance of laminated composites. In this study, plain-weave carbon fiber/epoxy composites were interleaved with nylon 6,6 nonwoven fabrics with an areal weight density of 17 gsm. The carbon fiber/epoxy composite laminates with/without nylon 6,6 nonwoven fabric interlayers were manufactured by VARTM technique. Double cantilever beam fracture toughness tests were carried out on the prepared composite test specimens in accordance with ASTM 5528 standard. The experimental test data were statistically analyzed by two-parameter Weibull distribution. The results showed that the initiation and propagation fracture toughness Mode-I fracture toughness of carbon fiber/epoxy composites could be improved by about 34 and 156% (corresponding to a reliability level of 0.50) with the incorporation of nylon 6,6 interlayers in the interlaminar region, respectively. The results also revealed that the percent increase in the propagation fracture toughness value was 67 and 41% at reliability levels of 0.90 and 0.95, respectively. |
Ay, Z; Tanoglu, M The Effect of Single-Walled Carbon Nanotube (SWCNT) Concentration on the Mechanical and Rheological Behavior of Epoxy Matrix Journal Article MECHANICS OF COMPOSITE MATERIALS, 56 (4), pp. 523-532, 2020, ISSN: 0191-5665. @article{ISI:000567735300002, title = {The Effect of Single-Walled Carbon Nanotube (SWCNT) Concentration on the Mechanical and Rheological Behavior of Epoxy Matrix}, author = {Z Ay and M Tanoglu}, doi = {10.1007/s11029-020-09900-7, Early Access Date = SEP 2020}, issn = {0191-5665}, year = {2020}, date = {2020-09-01}, journal = {MECHANICS OF COMPOSITE MATERIALS}, volume = {56}, number = {4}, pages = {523-532}, abstract = {The improvement of Mode I fracture toughness of epoxy by the addition of single-walled carbon nanotubes (SWCNTs) is considered. To prepare nanocomposites, chemical-vapor-deposition-grown SWCNTs noncovalently functionalized with an ethoxylated alcohol was used as the additive and a diglycidyl ether of bisphenol-A-based epoxy as the matrix material. The SWCNTs were dispersed in the epoxy matrix via a mechanical stirrer and a 3-roll mill. The effect of their concentration (0.0125, 0.025, 0.05, 0.1, 0.3, and 0.5 wt.%) on the mechanical properties of the nanocomposites was investigated, and the optimum concentration was determined. Mode I fracture toughness (single-edge-notch 3-point bending) and tensile tests were carried out on neat epoxy and SWCNT-reinforced epoxy nanocomposites. The fractured surfaces of fracture toughness and tensile test specimens were examined by the SEM to reveal the effect of SWCNTs on their failure modes.}, keywords = {}, pubstate = {published}, tppubtype = {article} } The improvement of Mode I fracture toughness of epoxy by the addition of single-walled carbon nanotubes (SWCNTs) is considered. To prepare nanocomposites, chemical-vapor-deposition-grown SWCNTs noncovalently functionalized with an ethoxylated alcohol was used as the additive and a diglycidyl ether of bisphenol-A-based epoxy as the matrix material. The SWCNTs were dispersed in the epoxy matrix via a mechanical stirrer and a 3-roll mill. The effect of their concentration (0.0125, 0.025, 0.05, 0.1, 0.3, and 0.5 wt.%) on the mechanical properties of the nanocomposites was investigated, and the optimum concentration was determined. Mode I fracture toughness (single-edge-notch 3-point bending) and tensile tests were carried out on neat epoxy and SWCNT-reinforced epoxy nanocomposites. The fractured surfaces of fracture toughness and tensile test specimens were examined by the SEM to reveal the effect of SWCNTs on their failure modes. |
Kangal, S; Kartav, O; Tanoğlu, M; Aktaş, E; Artem, H S Journal of Composite Materials, 54 (7), pp. 961-980, 2020. @article{Kangal2020961, title = {Investigation of interlayer hybridization effect on burst pressure performance of composite overwrapped pressure vessels with load-sharing metallic liner}, author = {S Kangal and O Kartav and M Tanoğlu and E Aktaş and H S Artem}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85071956589&doi=10.1177%2f0021998319870588&partnerID=40&md5=90d8ba513531b1cd09c963d447aebf4a}, doi = {10.1177/0021998319870588}, year = {2020}, date = {2020-01-01}, journal = {Journal of Composite Materials}, volume = {54}, number = {7}, pages = {961-980}, abstract = {In this study, multi-layered composite overwrapped pressure vessels for high-pressure gaseous storage were designed, modeled by finite element method and manufactured by filament winding technique. 34CrMo4 steel was selected as a load-sharing metallic liner. Glass and carbon filaments were overwrapped on the liner with a winding angle of [±11°/90°2]3 to obtain fully overwrapped composite reinforced vessel with non-identical front and back dome endings. The vessels were loaded with increasing internal pressure up to the burst pressure level. The mechanical performances of pressure vessels, (i) fully overwrapped with glass fibers and (ii) with additional two carbon hoop layers on the cylindrical section, were investigated by both experimental and numerical approaches. In numerical approaches, finite element analysis was performed featuring a simple progressive damage model available in ANSYS software package for the composite section. The metal liner was modeled as elastic–plastic material. The results reveal that the finite element model provides a good correlation between experimental and numerical strain results for the vessels, together with the indication of the positive effect on radial deformation of the COPVs due to the composite interlayer hybridization. The constructed model was also able to predict experimental burst pressures within a range of 8%. However, the experimental and finite element analysis results showed that hybridization of hoop layers did not have any significant impact on the burst pressure performance of the vessels. This finding was attributed to the change of load-sharing capacity of composite layers due to the stiffness difference of carbon and glass fibers. © The Author(s) 2019.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, multi-layered composite overwrapped pressure vessels for high-pressure gaseous storage were designed, modeled by finite element method and manufactured by filament winding technique. 34CrMo4 steel was selected as a load-sharing metallic liner. Glass and carbon filaments were overwrapped on the liner with a winding angle of [±11°/90°2]3 to obtain fully overwrapped composite reinforced vessel with non-identical front and back dome endings. The vessels were loaded with increasing internal pressure up to the burst pressure level. The mechanical performances of pressure vessels, (i) fully overwrapped with glass fibers and (ii) with additional two carbon hoop layers on the cylindrical section, were investigated by both experimental and numerical approaches. In numerical approaches, finite element analysis was performed featuring a simple progressive damage model available in ANSYS software package for the composite section. The metal liner was modeled as elastic–plastic material. The results reveal that the finite element model provides a good correlation between experimental and numerical strain results for the vessels, together with the indication of the positive effect on radial deformation of the COPVs due to the composite interlayer hybridization. The constructed model was also able to predict experimental burst pressures within a range of 8%. However, the experimental and finite element analysis results showed that hybridization of hoop layers did not have any significant impact on the burst pressure performance of the vessels. This finding was attributed to the change of load-sharing capacity of composite layers due to the stiffness difference of carbon and glass fibers. © The Author(s) 2019. |
Yardimci, Atike Ince; Tanoglu, Metin; Yilmaz, Selahattin; Selamet, Yusuf Effect of CNT incorporation on PAN/PPy nanofibers synthesized by electrospinning method Journal Article TURKISH JOURNAL OF CHEMISTRY, 44 (4), pp. 1002-1015, 2020, ISSN: 1300-0527. @article{ISI:000560919000010, title = {Effect of CNT incorporation on PAN/PPy nanofibers synthesized by electrospinning method}, author = {Atike Ince Yardimci and Metin Tanoglu and Selahattin Yilmaz and Yusuf Selamet}, doi = {10.3906/kim-1911-49}, issn = {1300-0527}, year = {2020}, date = {2020-01-01}, journal = {TURKISH JOURNAL OF CHEMISTRY}, volume = {44}, number = {4}, pages = {1002-1015}, abstract = {In this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold. |
2019 |
Beylergil, B; Tanoǧlu, M; Aktaş, E Mode-I fracture toughness of carbon fiber/epoxy composites interleaved by aramid nonwoven veils Journal Article Steel and Composite Structures, 31 (2), pp. 113-123, 2019. @article{Beylergil2019113, title = {Mode-I fracture toughness of carbon fiber/epoxy composites interleaved by aramid nonwoven veils}, author = {B Beylergil and M Tanoǧlu and E Aktaş}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85065238224&doi=10.12989%2fscs.2019.31.2.113&partnerID=40&md5=c8783b96f972924d7754bb7820373a14}, doi = {10.12989/scs.2019.31.2.113}, year = {2019}, date = {2019-01-01}, journal = {Steel and Composite Structures}, volume = {31}, number = {2}, pages = {113-123}, abstract = {In this study, carbon fiber/epoxy (CF/EP) composites were interleaved with aramid nonwoven veils with an areal weight density of 8.5 g/m 2 to improve their Mode-I fracture toughness. The control and aramid interleaved CF/EP composite laminates were manufactured by VARTM in a [0]4 configuration. Tensile, three-point bending, compression, interlaminar shear, Charpy impact and Mode-I (DCB) fracture toughness values were determined to evaluate the effects of aramid nonwoven fabrics on the mechanical performance of the CF/EP composites. Thermomechanical behavior of the specimens was investigated by Dynamic Mechanical Analysis (DMA). The results showed that the propagation Mode-I fracture toughness values of CF/EP composites can be significantly improved (by about 72%) using aramid nonwoven fabrics. It was found that the main extrinsic toughening mechanism is aramid microfiber bridging acting behind the crack-tip. The incorporation of these nonwovens also increased interlaminar shear and Charpy impact strength by 10 and 16.5%, respectively. Moreover, it was revealed that the damping ability of the composites increased with the incorporation of aramid nonwoven fabrics in the interlaminar region of composites. On the other hand, they caused a reduction in in-plane mechanical properties due to the reduced carbon fiber volume fraction, increased thickness and void formation in the composites. Copyright © 2019 Techno-Press, Ltd.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, carbon fiber/epoxy (CF/EP) composites were interleaved with aramid nonwoven veils with an areal weight density of 8.5 g/m 2 to improve their Mode-I fracture toughness. The control and aramid interleaved CF/EP composite laminates were manufactured by VARTM in a [0]4 configuration. Tensile, three-point bending, compression, interlaminar shear, Charpy impact and Mode-I (DCB) fracture toughness values were determined to evaluate the effects of aramid nonwoven fabrics on the mechanical performance of the CF/EP composites. Thermomechanical behavior of the specimens was investigated by Dynamic Mechanical Analysis (DMA). The results showed that the propagation Mode-I fracture toughness values of CF/EP composites can be significantly improved (by about 72%) using aramid nonwoven fabrics. It was found that the main extrinsic toughening mechanism is aramid microfiber bridging acting behind the crack-tip. The incorporation of these nonwovens also increased interlaminar shear and Charpy impact strength by 10 and 16.5%, respectively. Moreover, it was revealed that the damping ability of the composites increased with the incorporation of aramid nonwoven fabrics in the interlaminar region of composites. On the other hand, they caused a reduction in in-plane mechanical properties due to the reduced carbon fiber volume fraction, increased thickness and void formation in the composites. Copyright © 2019 Techno-Press, Ltd. |
2018 |
Oztoprak, N; Gunes, M D; Tanoglu, M; Aktas, E; Egilmez, O O; Senocak, C; Kulac, G Developing polymer composite-based leaf spring systems for automotive industry Journal Article Science and Engineering of Composite Materials, 25 (6), pp. 1167-1176, 2018. @article{Oztoprak20181167, title = {Developing polymer composite-based leaf spring systems for automotive industry}, author = {N Oztoprak and M D Gunes and M Tanoglu and E Aktas and O O Egilmez and C Senocak and G Kulac}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85056594508&doi=10.1515%2fsecm-2016-0335&partnerID=40&md5=f8692f0ca38d12eec3006c474b120b21}, doi = {10.1515/secm-2016-0335}, year = {2018}, date = {2018-01-01}, journal = {Science and Engineering of Composite Materials}, volume = {25}, number = {6}, pages = {1167-1176}, abstract = {Composite-based mono-leaf spring systems were designed and manufactured to replace existing mono-leaf metal leaf spring in a light commercial vehicle. In this study, experimentally obtained mechanical properties of different fiber-reinforced polymer materials are presented first, followed by the description of the finite element analytical model created in Abaqus 6.12-1 (Dassault Systemes Simulia Corp., RI, US) using the obtained properties. The results from the finite element analysis are presented next and compared with actual size experimental tests conducted on manufactured prototypes. The results demonstrated that the reinforcement type and orientation dramatically influenced the spring rate. The prototypes showed significant weight reduction of about 80% with improved mechanical properties. The hybrid composite systems can be utilized for composite-based leaf springs with considerable mechanical performance. © 2018 Walter de Gruyter GmbH, Berlin/Boston.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Composite-based mono-leaf spring systems were designed and manufactured to replace existing mono-leaf metal leaf spring in a light commercial vehicle. In this study, experimentally obtained mechanical properties of different fiber-reinforced polymer materials are presented first, followed by the description of the finite element analytical model created in Abaqus 6.12-1 (Dassault Systemes Simulia Corp., RI, US) using the obtained properties. The results from the finite element analysis are presented next and compared with actual size experimental tests conducted on manufactured prototypes. The results demonstrated that the reinforcement type and orientation dramatically influenced the spring rate. The prototypes showed significant weight reduction of about 80% with improved mechanical properties. The hybrid composite systems can be utilized for composite-based leaf springs with considerable mechanical performance. © 2018 Walter de Gruyter GmbH, Berlin/Boston. |
Beylergil, B; Tanoğlu, M; Aktaş, E Effect of polyamide-6,6 (PA 66) nonwoven veils on the mechanical performance of carbon fiber/epoxy composites Journal Article Composite Structures, 194 , pp. 21-35, 2018. @article{Beylergil201821, title = {Effect of polyamide-6,6 (PA 66) nonwoven veils on the mechanical performance of carbon fiber/epoxy composites}, author = {B Beylergil and M Tanoğlu and E Aktaş}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85044992271&doi=10.1016%2fj.compstruct.2018.03.097&partnerID=40&md5=5a48cd887d9aa73061331019a3e6b047}, doi = {10.1016/j.compstruct.2018.03.097}, year = {2018}, date = {2018-01-01}, journal = {Composite Structures}, volume = {194}, pages = {21-35}, abstract = {In this study, carbon fiber/epoxy (CF/EP) composites were interleaved with polyamide-6,6 (PA 66) nonwoven veils at two different areal weight densities (17 and 50 gsm) to improve their delamination resistance against Mode-I loading. Mode-I fracture toughness (DCB), tensile, open hole tensile (OHT), flexural, compression, short beam shear (ILSS) and Charpy-impact tests were performed on the reference and PA 66 interleaved composite specimens. The DCB test results showed that the initiation and propagation Mode-I fracture toughness values of the composites were significantly improved by 84 and 171% using PA 66-17 gsm veils respectively, as compared to reference laminates. The use of denser PA 66-50 gsm veils in the interlaminar region led to higher improvement in fracture toughness values (349% for initiation and 718% for propagation) due to the higher amount of veil fibers involved in fiber bridging toughening mechanism. The incorporation of PA 66-50 gsm nonwoven veils also increased the ILSS and Charpy impact strength of the composites by 25 and 15%, respectively. On the other hand, the PA 66 veils reduced in-plane mechanical properties of CF/EP composites due to lower carbon fiber volume fraction and increased thickness. © 2018}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, carbon fiber/epoxy (CF/EP) composites were interleaved with polyamide-6,6 (PA 66) nonwoven veils at two different areal weight densities (17 and 50 gsm) to improve their delamination resistance against Mode-I loading. Mode-I fracture toughness (DCB), tensile, open hole tensile (OHT), flexural, compression, short beam shear (ILSS) and Charpy-impact tests were performed on the reference and PA 66 interleaved composite specimens. The DCB test results showed that the initiation and propagation Mode-I fracture toughness values of the composites were significantly improved by 84 and 171% using PA 66-17 gsm veils respectively, as compared to reference laminates. The use of denser PA 66-50 gsm veils in the interlaminar region led to higher improvement in fracture toughness values (349% for initiation and 718% for propagation) due to the higher amount of veil fibers involved in fiber bridging toughening mechanism. The incorporation of PA 66-50 gsm nonwoven veils also increased the ILSS and Charpy impact strength of the composites by 25 and 15%, respectively. On the other hand, the PA 66 veils reduced in-plane mechanical properties of CF/EP composites due to lower carbon fiber volume fraction and increased thickness. © 2018 |
Kandemir, S Development of Graphene Nanoplatelet-Reinforced AZ91 Magnesium Alloy by Solidification Processing Journal Article Journal of Materials Engineering and Performance, 27 (6), pp. 3014-3023, 2018. @article{Kandemir20183014, title = {Development of Graphene Nanoplatelet-Reinforced AZ91 Magnesium Alloy by Solidification Processing}, author = {S Kandemir}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85046038152&doi=10.1007%2fs11665-018-3391-x&partnerID=40&md5=1915050ebdd364d0e0e99a6144a89c16}, doi = {10.1007/s11665-018-3391-x}, year = {2018}, date = {2018-01-01}, journal = {Journal of Materials Engineering and Performance}, volume = {27}, number = {6}, pages = {3014-3023}, abstract = {It is a challenging task to effectively incorporate graphene nanoplatelets (GNPs) which have recently emerged as potential reinforcement for strengthening metals into magnesium-based matrices by conventional solidification processes due to their large surface areas and poor wettability. A solidification processing which combines mechanical stirring and ultrasonic dispersion of reinforcements in liquid matrix was employed to develop AZ91 magnesium alloy matrix composites reinforced with 0.25 and 0.5 wt.% GNPs. The microstructural studies conducted with scanning and transmission electron microscopes revealed that fairly uniform distribution and dispersion of GNPs through the matrix were achieved due to effective combination of mechanical and ultrasonic stirring. The GNPs embedded into the magnesium matrix led to significant enhancement in the hardness, tensile strength and ductility of the composites compared to those of unreinforced AZ91 alloy. The strength enhancement was predominantly attributed to the grain refinement by the GNP addition and dislocation generation strengthening due to the coefficient of thermal expansion mismatch between the matrix and reinforcement. The improved ductility was attributed to the refinement of β eutectics by transforming from lamellar to the divorced eutectics due to the GNP additions. In addition, the strengthening efficiency of the composite with 0.25 wt.% GNP was found to be higher than those of the composite with 0.5 wt.% GNP as the agglomeration tendency of GNPs is increased with increasing GNP content. These results were compared with those of the GNP-reinforced magnesium composites reported in the literature, indicating the potential of the process introduced in this study in terms of fabricating light and high-performance metal matrix composites. © 2018, ASM International.}, keywords = {}, pubstate = {published}, tppubtype = {article} } It is a challenging task to effectively incorporate graphene nanoplatelets (GNPs) which have recently emerged as potential reinforcement for strengthening metals into magnesium-based matrices by conventional solidification processes due to their large surface areas and poor wettability. A solidification processing which combines mechanical stirring and ultrasonic dispersion of reinforcements in liquid matrix was employed to develop AZ91 magnesium alloy matrix composites reinforced with 0.25 and 0.5 wt.% GNPs. The microstructural studies conducted with scanning and transmission electron microscopes revealed that fairly uniform distribution and dispersion of GNPs through the matrix were achieved due to effective combination of mechanical and ultrasonic stirring. The GNPs embedded into the magnesium matrix led to significant enhancement in the hardness, tensile strength and ductility of the composites compared to those of unreinforced AZ91 alloy. The strength enhancement was predominantly attributed to the grain refinement by the GNP addition and dislocation generation strengthening due to the coefficient of thermal expansion mismatch between the matrix and reinforcement. The improved ductility was attributed to the refinement of β eutectics by transforming from lamellar to the divorced eutectics due to the GNP additions. In addition, the strengthening efficiency of the composite with 0.25 wt.% GNP was found to be higher than those of the composite with 0.5 wt.% GNP as the agglomeration tendency of GNPs is increased with increasing GNP content. These results were compared with those of the GNP-reinforced magnesium composites reported in the literature, indicating the potential of the process introduced in this study in terms of fabricating light and high-performance metal matrix composites. © 2018, ASM International. |
Kandemir, S Development of Graphene Nanoplatelet-Reinforced AZ91 Magnesium Alloy by Solidification Processing Journal Article Journal of Materials Engineering and Performance, 27 (6), pp. 3014-3023, 2018. @article{Kandemir20183014b, title = {Development of Graphene Nanoplatelet-Reinforced AZ91 Magnesium Alloy by Solidification Processing}, author = {S Kandemir}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85046038152&doi=10.1007%2fs11665-018-3391-x&partnerID=40&md5=1915050ebdd364d0e0e99a6144a89c16}, doi = {10.1007/s11665-018-3391-x}, year = {2018}, date = {2018-01-01}, journal = {Journal of Materials Engineering and Performance}, volume = {27}, number = {6}, pages = {3014-3023}, abstract = {It is a challenging task to effectively incorporate graphene nanoplatelets (GNPs) which have recently emerged as potential reinforcement for strengthening metals into magnesium-based matrices by conventional solidification processes due to their large surface areas and poor wettability. A solidification processing which combines mechanical stirring and ultrasonic dispersion of reinforcements in liquid matrix was employed to develop AZ91 magnesium alloy matrix composites reinforced with 0.25 and 0.5 wt.% GNPs. The microstructural studies conducted with scanning and transmission electron microscopes revealed that fairly uniform distribution and dispersion of GNPs through the matrix were achieved due to effective combination of mechanical and ultrasonic stirring. The GNPs embedded into the magnesium matrix led to significant enhancement in the hardness, tensile strength and ductility of the composites compared to those of unreinforced AZ91 alloy. The strength enhancement was predominantly attributed to the grain refinement by the GNP addition and dislocation generation strengthening due to the coefficient of thermal expansion mismatch between the matrix and reinforcement. The improved ductility was attributed to the refinement of β eutectics by transforming from lamellar to the divorced eutectics due to the GNP additions. In addition, the strengthening efficiency of the composite with 0.25 wt.% GNP was found to be higher than those of the composite with 0.5 wt.% GNP as the agglomeration tendency of GNPs is increased with increasing GNP content. These results were compared with those of the GNP-reinforced magnesium composites reported in the literature, indicating the potential of the process introduced in this study in terms of fabricating light and high-performance metal matrix composites. © 2018, ASM International.}, keywords = {}, pubstate = {published}, tppubtype = {article} } It is a challenging task to effectively incorporate graphene nanoplatelets (GNPs) which have recently emerged as potential reinforcement for strengthening metals into magnesium-based matrices by conventional solidification processes due to their large surface areas and poor wettability. A solidification processing which combines mechanical stirring and ultrasonic dispersion of reinforcements in liquid matrix was employed to develop AZ91 magnesium alloy matrix composites reinforced with 0.25 and 0.5 wt.% GNPs. The microstructural studies conducted with scanning and transmission electron microscopes revealed that fairly uniform distribution and dispersion of GNPs through the matrix were achieved due to effective combination of mechanical and ultrasonic stirring. The GNPs embedded into the magnesium matrix led to significant enhancement in the hardness, tensile strength and ductility of the composites compared to those of unreinforced AZ91 alloy. The strength enhancement was predominantly attributed to the grain refinement by the GNP addition and dislocation generation strengthening due to the coefficient of thermal expansion mismatch between the matrix and reinforcement. The improved ductility was attributed to the refinement of β eutectics by transforming from lamellar to the divorced eutectics due to the GNP additions. In addition, the strengthening efficiency of the composite with 0.25 wt.% GNP was found to be higher than those of the composite with 0.5 wt.% GNP as the agglomeration tendency of GNPs is increased with increasing GNP content. These results were compared with those of the GNP-reinforced magnesium composites reported in the literature, indicating the potential of the process introduced in this study in terms of fabricating light and high-performance metal matrix composites. © 2018, ASM International. |
2017 |
Ma, Luoning; Xie, Kelvin Y; Toksoy, Muhammet F; Kuwelkar, Kanak; Haber, Richard A; Hemker, Kevin J The effect of Si on the microstructure and mechanical properties of spark plasma sintered boron carbide Journal Article MATERIALS CHARACTERIZATION, 134 , pp. 274-278, 2017, ISSN: 1044-5803. @article{ISI:000419416400031, title = {The effect of Si on the microstructure and mechanical properties of spark plasma sintered boron carbide}, author = {Luoning Ma and Kelvin Y Xie and Muhammet F Toksoy and Kanak Kuwelkar and Richard A Haber and Kevin J Hemker}, doi = {10.1016/j.matchar.2017.11.010}, issn = {1044-5803}, year = {2017}, date = {2017-12-01}, journal = {MATERIALS CHARACTERIZATION}, volume = {134}, pages = {274-278}, abstract = {Fully dense boron carbide discs were achieved by spark plasma sintering boron carbide powders with 10 wt% silicon. The silicon did not diffuse into boron carbide grains to produce a solid solution of Si-doped boron carbide; instead the silicon reacted with impurities in the starting powder to form beta-SiC and borosilicate glass. The resultant new phases facilitated densification of the multiphase ceramic through liquid phase-assisted sintering. The resultant material exhibits improved hardness (34.3 GPa Vikers hardness under 1 kg load) with toughness comparable to both Si-free and commercially available boron carbide.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Fully dense boron carbide discs were achieved by spark plasma sintering boron carbide powders with 10 wt% silicon. The silicon did not diffuse into boron carbide grains to produce a solid solution of Si-doped boron carbide; instead the silicon reacted with impurities in the starting powder to form beta-SiC and borosilicate glass. The resultant new phases facilitated densification of the multiphase ceramic through liquid phase-assisted sintering. The resultant material exhibits improved hardness (34.3 GPa Vikers hardness under 1 kg load) with toughness comparable to both Si-free and commercially available boron carbide. |
Kandemir, Sinan Effects of TiB2 nanoparticle content on the microstructure and mechanical properties of aluminum matrix nanocomposites Journal Article MATERIALS TESTING, 59 (10), pp. 844-852, 2017, ISSN: 0025-5300. @article{ISI:000415695400003, title = {Effects of TiB2 nanoparticle content on the microstructure and mechanical properties of aluminum matrix nanocomposites}, author = {Sinan Kandemir}, doi = {10.3139/120.111079}, issn = {0025-5300}, year = {2017}, date = {2017-10-01}, journal = {MATERIALS TESTING}, volume = {59}, number = {10}, pages = {844-852}, abstract = {The present work reports the fabrication of A357 alloy matrix nanocomposites reinforced with 0.5, 1.0 and 2.0 wt.-% TiB2 nanoparticles (20-30 nm) by a novel method which is the combination of semi-solid mechanical mixing and ultrasonic dispersion of nanoparticles in liquid state. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicated that reasonably effective deagglomeration and uniform distribution of TiB2 nanoparticles into the matrix were achieved. Transmission electron microscopy studies also confirmed that the nanoparticles were embedded into the matrix and a good bonding was obtained between the matrix and the reinforcement. Increasing nanoparticle content led to grain refinement and significant enhancement in the mechanical properties of nanocomposites. The addition of 0.5, 1.0, and 2.0 wt.-% TiB2 nanoparticles increased the 0.2 % proof stress of matrix alloy by approximately 31, 48 and 61 %, respectively. The contribution of different mechanisms to the strength enhancement is discussed. It is proposed that the strengthening is mainly due to Orowan mechanism and dislocation generation effect by the coefficient of thermal expansion mismatch between the TiB2 nanoparticles and the matrix.}, keywords = {}, pubstate = {published}, tppubtype = {article} } The present work reports the fabrication of A357 alloy matrix nanocomposites reinforced with 0.5, 1.0 and 2.0 wt.-% TiB2 nanoparticles (20-30 nm) by a novel method which is the combination of semi-solid mechanical mixing and ultrasonic dispersion of nanoparticles in liquid state. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicated that reasonably effective deagglomeration and uniform distribution of TiB2 nanoparticles into the matrix were achieved. Transmission electron microscopy studies also confirmed that the nanoparticles were embedded into the matrix and a good bonding was obtained between the matrix and the reinforcement. Increasing nanoparticle content led to grain refinement and significant enhancement in the mechanical properties of nanocomposites. The addition of 0.5, 1.0, and 2.0 wt.-% TiB2 nanoparticles increased the 0.2 % proof stress of matrix alloy by approximately 31, 48 and 61 %, respectively. The contribution of different mechanisms to the strength enhancement is discussed. It is proposed that the strengthening is mainly due to Orowan mechanism and dislocation generation effect by the coefficient of thermal expansion mismatch between the TiB2 nanoparticles and the matrix. |
Beylergil, Bertan; Tanoglu, Metin; Aktas, Engin Enhancement of interlaminar fracture toughness of carbon fiber-epoxy composites using polyamide-6,6 electrospun nanofibers Journal Article JOURNAL OF APPLIED POLYMER SCIENCE, 134 (35), 2017, ISSN: 0021-8995. @article{ISI:000403346000012, title = {Enhancement of interlaminar fracture toughness of carbon fiber-epoxy composites using polyamide-6,6 electrospun nanofibers}, author = {Bertan Beylergil and Metin Tanoglu and Engin Aktas}, doi = {10.1002/app.45244}, issn = {0021-8995}, year = {2017}, date = {2017-09-01}, journal = {JOURNAL OF APPLIED POLYMER SCIENCE}, volume = {134}, number = {35}, abstract = {In this study, carbon fiber-epoxy composites are interleaved with electrospun polyamide-6,6 (PA 66) nanofibers to improve their Mode-I fracture toughness. These nanofibers are directly deposited onto carbon fabrics before composite manufacturing via vacuum infusion. Three-point bending, tensile, compression, interlaminar shear strength, Charpy impact, and double cantilever beam tests are performed on the reference and PA 66 interleaved specimens to evaluate the effects of PA 66 nanofibers on the mechanical properties of composites. To investigate the effect of nanofiber areal weight density (AWD), nanointerlayers with various AWD are prepared by changing the electrospinning duration. It is found that the electrospun PA 66 nanofibers are very effective in improving Mode-I toughness and impact resistance, compressive strength, flexural modulus, and strength of the composites. However, these nanofibers cause a decrease in the tensile strength of the composites. The glass-transition temperature of the composites is not affected by the addition of PA 66 nanofibers. (c) 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45244.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, carbon fiber-epoxy composites are interleaved with electrospun polyamide-6,6 (PA 66) nanofibers to improve their Mode-I fracture toughness. These nanofibers are directly deposited onto carbon fabrics before composite manufacturing via vacuum infusion. Three-point bending, tensile, compression, interlaminar shear strength, Charpy impact, and double cantilever beam tests are performed on the reference and PA 66 interleaved specimens to evaluate the effects of PA 66 nanofibers on the mechanical properties of composites. To investigate the effect of nanofiber areal weight density (AWD), nanointerlayers with various AWD are prepared by changing the electrospinning duration. It is found that the electrospun PA 66 nanofibers are very effective in improving Mode-I toughness and impact resistance, compressive strength, flexural modulus, and strength of the composites. However, these nanofibers cause a decrease in the tensile strength of the composites. The glass-transition temperature of the composites is not affected by the addition of PA 66 nanofibers. (c) 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45244. |
Toksoy, Muhammet Fatih; Rafaniello, William; Xie, Kelvin Yu; Ma, Luoning; Hemker, Kevin Jude; Haber, Richard Alan Densification and characterization of rapid carbothermal synthesized boron carbide Journal Article INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY, 14 (3), pp. 443-453, 2017, ISSN: 1546-542X. @article{ISI:000404259000018, title = {Densification and characterization of rapid carbothermal synthesized boron carbide}, author = {Muhammet Fatih Toksoy and William Rafaniello and Kelvin Yu Xie and Luoning Ma and Kevin Jude Hemker and Richard Alan Haber}, doi = {10.1111/ijac.12654}, issn = {1546-542X}, year = {2017}, date = {2017-05-01}, journal = {INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY}, volume = {14}, number = {3}, pages = {443-453}, abstract = {Submicrometer boron carbide powders were synthesized using rapid carbothermal reduction (RCR) method. Synthesized boron carbide powders had smaller particle size, lower free carbon, and high density of twins compared to commercial samples. Powders were sintered using spark plasma sintering at different temperatures and dwell times to compare sintering behavior. Synthesized boron carbide powders reached >99% TD at lower temperature and shorter dwell times compared to commercial powders. Improved microhardness observed in the densified RCR samples was likely caused by the combination of higher purity, better stoichiometry control, finer grain size, and a higher density of twin boundaries.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Submicrometer boron carbide powders were synthesized using rapid carbothermal reduction (RCR) method. Synthesized boron carbide powders had smaller particle size, lower free carbon, and high density of twins compared to commercial samples. Powders were sintered using spark plasma sintering at different temperatures and dwell times to compare sintering behavior. Synthesized boron carbide powders reached >99% TD at lower temperature and shorter dwell times compared to commercial powders. Improved microhardness observed in the densified RCR samples was likely caused by the combination of higher purity, better stoichiometry control, finer grain size, and a higher density of twin boundaries. |
Kandemir, Sinan JOURNAL OF COMPOSITE MATERIALS, 51 (3), pp. 395-404, 2017, ISSN: 0021-9983. @article{ISI:000394801300009, title = {Microstructure and mechanical properties of A357/SiC nanocomposites fabricated by ultrasonic cavitation-based dispersion of ball-milled nanoparticles}, author = {Sinan Kandemir}, doi = {10.1177/0021998316644850}, issn = {0021-9983}, year = {2017}, date = {2017-02-01}, journal = {JOURNAL OF COMPOSITE MATERIALS}, volume = {51}, number = {3}, pages = {395-404}, abstract = {In this work, A357/0.5wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30nm) and aluminium powders (<75 mu m) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this work, A357/0.5wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30nm) and aluminium powders (<75 mu m) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface. |
Beylergil, B; Tanoğlu, M; Aktaş, E Enhancement of interlaminar fracture toughness of carbon fiber–epoxy composites using polyamide-6,6 electrospun nanofibers Journal Article Journal of Applied Polymer Science, 134 (35), 2017. @article{Beylergil2017, title = {Enhancement of interlaminar fracture toughness of carbon fiber–epoxy composites using polyamide-6,6 electrospun nanofibers}, author = {B Beylergil and M Tanoğlu and E Aktaş}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85019089440&doi=10.1002%2fapp.45244&partnerID=40&md5=ef8bdba44c46b9b1bc9aaedfbbbde061}, doi = {10.1002/app.45244}, year = {2017}, date = {2017-01-01}, journal = {Journal of Applied Polymer Science}, volume = {134}, number = {35}, abstract = {In this study, carbon fiber–epoxy composites are interleaved with electrospun polyamide-6,6 (PA 66) nanofibers to improve their Mode-I fracture toughness. These nanofibers are directly deposited onto carbon fabrics before composite manufacturing via vacuum infusion. Three-point bending, tensile, compression, interlaminar shear strength, Charpy impact, and double cantilever beam tests are performed on the reference and PA 66 interleaved specimens to evaluate the effects of PA 66 nanofibers on the mechanical properties of composites. To investigate the effect of nanofiber areal weight density (AWD), nanointerlayers with various AWD are prepared by changing the electrospinning duration. It is found that the electrospun PA 66 nanofibers are very effective in improving Mode-I toughness and impact resistance, compressive strength, flexural modulus, and strength of the composites. However, these nanofibers cause a decrease in the tensile strength of the composites. The glass-transition temperature of the composites is not affected by the addition of PA 66 nanofibers. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45244. © 2017 Wiley Periodicals, Inc.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, carbon fiber–epoxy composites are interleaved with electrospun polyamide-6,6 (PA 66) nanofibers to improve their Mode-I fracture toughness. These nanofibers are directly deposited onto carbon fabrics before composite manufacturing via vacuum infusion. Three-point bending, tensile, compression, interlaminar shear strength, Charpy impact, and double cantilever beam tests are performed on the reference and PA 66 interleaved specimens to evaluate the effects of PA 66 nanofibers on the mechanical properties of composites. To investigate the effect of nanofiber areal weight density (AWD), nanointerlayers with various AWD are prepared by changing the electrospinning duration. It is found that the electrospun PA 66 nanofibers are very effective in improving Mode-I toughness and impact resistance, compressive strength, flexural modulus, and strength of the composites. However, these nanofibers cause a decrease in the tensile strength of the composites. The glass-transition temperature of the composites is not affected by the addition of PA 66 nanofibers. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45244. © 2017 Wiley Periodicals, Inc. |
Kandemir, S Journal of Composite Materials, 51 (3), pp. 395-404, 2017. @article{Kandemir2017395, title = {Microstructure and mechanical properties of A357/SiC nanocomposites fabricated by ultrasonic cavitation-based dispersion of ball-milled nanoparticles}, author = {S Kandemir}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85011573357&doi=10.1177%2f0021998316644850&partnerID=40&md5=1c26ba4dde5d58581fb0feb8fa56d880}, doi = {10.1177/0021998316644850}, year = {2017}, date = {2017-01-01}, journal = {Journal of Composite Materials}, volume = {51}, number = {3}, pages = {395-404}, abstract = {In this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30 nm) and aluminium powders (<75 μm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface. © The Author(s) 2016.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30 nm) and aluminium powders (<75 μm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface. © The Author(s) 2016. |
Kandemir, S Journal of Composite Materials, 51 (3), pp. 395-404, 2017. @article{Kandemir2017395b, title = {Microstructure and mechanical properties of A357/SiC nanocomposites fabricated by ultrasonic cavitation-based dispersion of ball-milled nanoparticles}, author = {S Kandemir}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-85011573357&doi=10.1177%2f0021998316644850&partnerID=40&md5=1c26ba4dde5d58581fb0feb8fa56d880}, doi = {10.1177/0021998316644850}, year = {2017}, date = {2017-01-01}, journal = {Journal of Composite Materials}, volume = {51}, number = {3}, pages = {395-404}, abstract = {In this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30 nm) and aluminium powders (<75 μm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface. © The Author(s) 2016.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30 nm) and aluminium powders (<75 μm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface. © The Author(s) 2016. |
2016 |
An, Qi; III, William Goddard A; Xie, Kelvin Y; Sim, Gi-dong; Hemker, Kevin J; Munhollon, Tyler; Toksoy, Fatih M; Haber, Richard A Superstrength through Nanotwinning Journal Article NANO LETTERS, 16 (12), pp. 7573-7579, 2016, ISSN: 1530-6984. @article{ISI:000389963200038, title = {Superstrength through Nanotwinning}, author = {Qi An and William A Goddard III and Kelvin Y Xie and Gi-dong Sim and Kevin J Hemker and Tyler Munhollon and Fatih M Toksoy and Richard A Haber}, doi = {10.1021/acs.nanolett.6b03414}, issn = {1530-6984}, year = {2016}, date = {2016-12-01}, journal = {NANO LETTERS}, volume = {16}, number = {12}, pages = {7573-7579}, abstract = {The theoretical strength of a material is the minimum stress to deform or fracture the perfect single crystal material that has no defects. This theoretical strength is considered as an upper bound on the attainable strength for a real crystal. In contradiction to this expectation, we use quantum mechanics (QM) simulations to show that for the boron carbide (B4C) hard ceramic, this theoretical shear strength can be exceeded by 11% by imposing nanoscale twins. We also predict from QM that the indentation strength of nanotwinned B4C is 12% higher than that of the perfect crystal. Further, we validate this effect experimentally, showing that nanotwinned samples are harder by 2.3% than the twin-free counterpart of B4C. The origin of this strengthening mechanism is suppression of twin boundary (TB) slip within the nanotwins due to the directional nature of covalent bonds at the TB.}, keywords = {}, pubstate = {published}, tppubtype = {article} } The theoretical strength of a material is the minimum stress to deform or fracture the perfect single crystal material that has no defects. This theoretical strength is considered as an upper bound on the attainable strength for a real crystal. In contradiction to this expectation, we use quantum mechanics (QM) simulations to show that for the boron carbide (B4C) hard ceramic, this theoretical shear strength can be exceeded by 11% by imposing nanoscale twins. We also predict from QM that the indentation strength of nanotwinned B4C is 12% higher than that of the perfect crystal. Further, we validate this effect experimentally, showing that nanotwinned samples are harder by 2.3% than the twin-free counterpart of B4C. The origin of this strengthening mechanism is suppression of twin boundary (TB) slip within the nanotwins due to the directional nature of covalent bonds at the TB. |
Sindirac, Can; Akkurt, Sedat Formation of La1-xSrxCo1-yFeyO3-delta cathode materials from precursor salts by heating in contact with CGO electrolyte Journal Article INTERNATIONAL JOURNAL OF HYDROGEN ENERGY, 41 (40), pp. 18157-18165, 2016, ISSN: 0360-3199. @article{ISI:000384852200041, title = {Formation of La1-xSrxCo1-yFeyO3-delta cathode materials from precursor salts by heating in contact with CGO electrolyte}, author = {Can Sindirac and Sedat Akkurt}, doi = {10.1016/j.ijhydene.2016.07.143}, issn = {0360-3199}, year = {2016}, date = {2016-10-01}, journal = {INTERNATIONAL JOURNAL OF HYDROGEN ENERGY}, volume = {41}, number = {40}, pages = {18157-18165}, abstract = {The purpose of this study is to determine the solid state reactions leading to the formation of La0.6Sr0.4Co0.8Fe0.2O3 and La0.6Sr0.4Co0.2Fe0.8O3 which are widely used as cathode material in solid oxide fuel cells (SOFC) from precursor salts. Interactions between the cathode and the electrolyte layers are also investigated while the cathode layer formed upon heating in contact with the surface of cerium -gadolinium oxide (CGO) electrolyte substrates. Almost all combinations of precursor salt mixtures were tested to see if all solid state reactions are completed and what phases eventually formed. Most of the transformation was complete after 1050 degrees C heat treatment to yield different mixed oxides. The cathode layer was usually in porous form but was found to spread well over the substrate. Uneven diffusion of La, Sr, Co or Fe into the substrate influenced the stoichiometry of the resulting cathode layer in varying degrees. Fe was found to diffuse into the substrate. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.}, keywords = {}, pubstate = {published}, tppubtype = {article} } The purpose of this study is to determine the solid state reactions leading to the formation of La0.6Sr0.4Co0.8Fe0.2O3 and La0.6Sr0.4Co0.2Fe0.8O3 which are widely used as cathode material in solid oxide fuel cells (SOFC) from precursor salts. Interactions between the cathode and the electrolyte layers are also investigated while the cathode layer formed upon heating in contact with the surface of cerium -gadolinium oxide (CGO) electrolyte substrates. Almost all combinations of precursor salt mixtures were tested to see if all solid state reactions are completed and what phases eventually formed. Most of the transformation was complete after 1050 degrees C heat treatment to yield different mixed oxides. The cathode layer was usually in porous form but was found to spread well over the substrate. Uneven diffusion of La, Sr, Co or Fe into the substrate influenced the stoichiometry of the resulting cathode layer in varying degrees. Fe was found to diffuse into the substrate. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved. |
Merter, Emrah N; Baser, Gulnur; Tanoglu, Metin JOURNAL OF COMPOSITE MATERIALS, 50 (12, SI), pp. 1697-1706, 2016, ISSN: 0021-9983. @article{ISI:000374328300014, title = {Effects of hybrid yarn preparation technique and fiber sizing on the mechanical properties of continuous glass fiber-reinforced polypropylene composites}, author = {Emrah N Merter and Gulnur Baser and Metin Tanoglu}, doi = {10.1177/0021998315595710}, issn = {0021-9983}, year = {2016}, date = {2016-05-01}, journal = {JOURNAL OF COMPOSITE MATERIALS}, volume = {50}, number = {12, SI}, pages = {1697-1706}, abstract = {In this study, hybrid yarns were developed by commingling the continuous polypropylene and glass fibers using air jet and direct twist preparation techniques. The non-crimp fabrics were obtained with +/- 45 degrees fiber orientation from these hybrid yarns. The fabrics were prepared with fiber sizings that are compatible and incompatible with polypropylene matrix to investigate the effect of interfacial adhesion on the properties of the thermoplastic composites. Composite panels were produced from the developed fabrics by hot press compression method and microstructural and mechanical properties of the composites were investigated. It was found that type of the hybrid yarn preparation technique and glass fiber sizing applied on the glass fibers have some important role on the properties of the composites. Composites made of fabrics produced by air jet hybrid yarn preparation technique exhibited better results than those produced by direct twist covering (single or double) hybrid yarn preparation techniques. The highest flexural properties (99.1MPa flexural strength and 9.55 GPa flexural modulus) were obtained from the composites manufactured from fabric containing compatible sizing, due to better adhesion at the interface of glass fibers and polypropylene matrix. The composite fabricated from fabric with polypropylene compatible sizing also exhibited the highest peel resistance (interlaminar peel strength value of 5.87N/mm). On the other hand, it was found that hybrid yarn preparation technique and type of the glass fiber sizing have insignificant effect on the impact properties of the glass fiber/polypropylene composites.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, hybrid yarns were developed by commingling the continuous polypropylene and glass fibers using air jet and direct twist preparation techniques. The non-crimp fabrics were obtained with +/- 45 degrees fiber orientation from these hybrid yarns. The fabrics were prepared with fiber sizings that are compatible and incompatible with polypropylene matrix to investigate the effect of interfacial adhesion on the properties of the thermoplastic composites. Composite panels were produced from the developed fabrics by hot press compression method and microstructural and mechanical properties of the composites were investigated. It was found that type of the hybrid yarn preparation technique and glass fiber sizing applied on the glass fibers have some important role on the properties of the composites. Composites made of fabrics produced by air jet hybrid yarn preparation technique exhibited better results than those produced by direct twist covering (single or double) hybrid yarn preparation techniques. The highest flexural properties (99.1MPa flexural strength and 9.55 GPa flexural modulus) were obtained from the composites manufactured from fabric containing compatible sizing, due to better adhesion at the interface of glass fibers and polypropylene matrix. The composite fabricated from fabric with polypropylene compatible sizing also exhibited the highest peel resistance (interlaminar peel strength value of 5.87N/mm). On the other hand, it was found that hybrid yarn preparation technique and type of the glass fiber sizing have insignificant effect on the impact properties of the glass fiber/polypropylene composites. |
Basturk, S B; Tanoglu, M; Cankaya, M A; Egilmez, O O Dynamic behavior predictions of fiber-metal laminate/aluminum foam sandwiches under various explosive weights Journal Article JOURNAL OF SANDWICH STRUCTURES & MATERIALS, 18 (3), pp. 321-342, 2016, ISSN: 1099-6362. @article{ISI:000375128600003b, title = {Dynamic behavior predictions of fiber-metal laminate/aluminum foam sandwiches under various explosive weights}, author = {S B Basturk and M Tanoglu and M A Cankaya and O O Egilmez}, doi = {10.1177/1099636215603036}, issn = {1099-6362}, year = {2016}, date = {2016-05-01}, journal = {JOURNAL OF SANDWICH STRUCTURES & MATERIALS}, volume = {18}, number = {3}, pages = {321-342}, abstract = {Application of blast tests causes some problems to characterize the performance of panels due to the drastic conditions of explosive medium. Real test has high safety concerns and is not easily accessible because of its extra budget. Some approaches are needed for the preliminary predictions of dynamic characteristics of panels under blast loading conditions. In this study, the response of sandwiches under blast effect was evaluated by combining quasi-static experiments and computational blast test data. The primary aim is to relate the quasi-static panel analysis to dynamic blast load. Based on this idea, lightweight sandwich composites were subjected to quasi-static compression loading with a special test apparatus and the samples were assumed as single degree-of-freedom mass-spring systems to include dynamic effect. This approach provides a simpler way to simulate the blast loading over the surface of the panels and reveals the possible failure mechanisms without applying any explosives. Therefore the design of the panels can be revised by considering quasi-static test results. In this work, the peak deflections and survivabilities of sandwiches for various explosive weights were predicted based on the formulations reported in the literature. Major failure types were also identified and evaluated with respect to their thicknesses.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Application of blast tests causes some problems to characterize the performance of panels due to the drastic conditions of explosive medium. Real test has high safety concerns and is not easily accessible because of its extra budget. Some approaches are needed for the preliminary predictions of dynamic characteristics of panels under blast loading conditions. In this study, the response of sandwiches under blast effect was evaluated by combining quasi-static experiments and computational blast test data. The primary aim is to relate the quasi-static panel analysis to dynamic blast load. Based on this idea, lightweight sandwich composites were subjected to quasi-static compression loading with a special test apparatus and the samples were assumed as single degree-of-freedom mass-spring systems to include dynamic effect. This approach provides a simpler way to simulate the blast loading over the surface of the panels and reveals the possible failure mechanisms without applying any explosives. Therefore the design of the panels can be revised by considering quasi-static test results. In this work, the peak deflections and survivabilities of sandwiches for various explosive weights were predicted based on the formulations reported in the literature. Major failure types were also identified and evaluated with respect to their thicknesses. |
Beylergil, B; Tanoǧlu, M; Aktaş, E Modification of carbon fibre/epoxy composites by polyvinyl alcohol (PVA) based electrospun nanofibres Journal Article Advanced Composites Letters, 25 (3), pp. 69-76, 2016. @article{Beylergil201669, title = {Modification of carbon fibre/epoxy composites by polyvinyl alcohol (PVA) based electrospun nanofibres}, author = {B Beylergil and M Tanoǧlu and E Aktaş}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-84977637333&partnerID=40&md5=eeaf6e446994c4a0238e3299047cf132}, year = {2016}, date = {2016-01-01}, journal = {Advanced Composites Letters}, volume = {25}, number = {3}, pages = {69-76}, abstract = {In this study, the effects of modifying interlaminar region of unidirectional carbon fibre/epoxy composites by the incorporation of electrospun polyvinyl alcohol (PVA) nanofibres were investigated. PVA nanofibres were directly deposited onto the carbon fabrics by electrospinning method to improve mechanical performance of those composites. The features of the electrospun nanofibres were characterized by microscopy techniques. The unidirectional carbon fibre/epoxy composite laminates with/without PVA nanofibre interlayers were manufactured by vacuum-infusion technique in a [0]4 configuration. Tensile, three-point bending, compression, Charpy-impact and Mode-I fracture toughness tests (Double Cantilever Beam (DCB)) were carried out in accordance with ASTM standards to evaluate mechanical performance of the composites. Scanning electron microscopy (SEM) observations were made on the specimens to evaluate microstructural features. It was observed that the carbon fabrics were successfully coated with a thin layer of PVA nanofibres by electrospinning technique. The results showed that P VA nanofibres improve the mechanical properties of unidirectional carbon/epoxy composite laminates when subjected to in-plane loading. On the other hand, PVA nanofibres slightly reduced the mode-I fracture toughness values although they led to more stable crack propagation.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, the effects of modifying interlaminar region of unidirectional carbon fibre/epoxy composites by the incorporation of electrospun polyvinyl alcohol (PVA) nanofibres were investigated. PVA nanofibres were directly deposited onto the carbon fabrics by electrospinning method to improve mechanical performance of those composites. The features of the electrospun nanofibres were characterized by microscopy techniques. The unidirectional carbon fibre/epoxy composite laminates with/without PVA nanofibre interlayers were manufactured by vacuum-infusion technique in a [0]4 configuration. Tensile, three-point bending, compression, Charpy-impact and Mode-I fracture toughness tests (Double Cantilever Beam (DCB)) were carried out in accordance with ASTM standards to evaluate mechanical performance of the composites. Scanning electron microscopy (SEM) observations were made on the specimens to evaluate microstructural features. It was observed that the carbon fabrics were successfully coated with a thin layer of PVA nanofibres by electrospinning technique. The results showed that P VA nanofibres improve the mechanical properties of unidirectional carbon/epoxy composite laminates when subjected to in-plane loading. On the other hand, PVA nanofibres slightly reduced the mode-I fracture toughness values although they led to more stable crack propagation. |
Merter, Emrah N; Başer, Gülnur; Tanoğlu, Metin Journal of Composite Materials, 50 (12), pp. 1697-1706, 2016. @article{doi:10.1177/0021998315595710, title = {Effects of hybrid yarn preparation technique and fiber sizing on the mechanical properties of continuous glass fiber-reinforced polypropylene composites}, author = {Emrah N Merter and Gülnur Başer and Metin Tanoğlu}, url = {https://doi.org/10.1177/0021998315595710}, doi = {10.1177/0021998315595710}, year = {2016}, date = {2016-01-01}, journal = {Journal of Composite Materials}, volume = {50}, number = {12}, pages = {1697-1706}, abstract = {In this study, hybrid yarns were developed by commingling the continuous polypropylene and glass fibers using air jet and direct twist preparation techniques. The non-crimp fabrics were obtained with ± 45 ° fiber orientation from these hybrid yarns. The fabrics were prepared with fiber sizings that are compatible and incompatible with polypropylene matrix to investigate the effect of interfacial adhesion on the properties of the thermoplastic composites. Composite panels were produced from the developed fabrics by hot press compression method and microstructural and mechanical properties of the composites were investigated. It was found that type of the hybrid yarn preparation technique and glass fiber sizing applied on the glass fibers have some important role on the properties of the composites. Composites made of fabrics produced by air jet hybrid yarn preparation technique exhibited better results than those produced by direct twist covering (single or double) hybrid yarn preparation techniques. The highest flexural properties (99.1 MPa flexural strength and 9.55 GPa flexural modulus) were obtained from the composites manufactured from fabric containing compatible sizing, due to better adhesion at the interface of glass fibers and polypropylene matrix. The composite fabricated from fabric with polypropylene compatible sizing also exhibited the highest peel resistance (interlaminar peel strength value of 5.87 N/mm). On the other hand, it was found that hybrid yarn preparation technique and type of the glass fiber sizing have insignificant effect on the impact properties of the glass fiber/polypropylene composites.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, hybrid yarns were developed by commingling the continuous polypropylene and glass fibers using air jet and direct twist preparation techniques. The non-crimp fabrics were obtained with ± 45 ° fiber orientation from these hybrid yarns. The fabrics were prepared with fiber sizings that are compatible and incompatible with polypropylene matrix to investigate the effect of interfacial adhesion on the properties of the thermoplastic composites. Composite panels were produced from the developed fabrics by hot press compression method and microstructural and mechanical properties of the composites were investigated. It was found that type of the hybrid yarn preparation technique and glass fiber sizing applied on the glass fibers have some important role on the properties of the composites. Composites made of fabrics produced by air jet hybrid yarn preparation technique exhibited better results than those produced by direct twist covering (single or double) hybrid yarn preparation techniques. The highest flexural properties (99.1 MPa flexural strength and 9.55 GPa flexural modulus) were obtained from the composites manufactured from fabric containing compatible sizing, due to better adhesion at the interface of glass fibers and polypropylene matrix. The composite fabricated from fabric with polypropylene compatible sizing also exhibited the highest peel resistance (interlaminar peel strength value of 5.87 N/mm). On the other hand, it was found that hybrid yarn preparation technique and type of the glass fiber sizing have insignificant effect on the impact properties of the glass fiber/polypropylene composites. |
Baştürk, SB; Tanoğlu, M; Çankaya, MA; Eğilmez, OÖ Dynamic behavior predictions of fiber-metal laminate/aluminum foam sandwiches under various explosive weights Journal Article Journal of Sandwich Structures & Materials, 18 (3), pp. 321-342, 2016. @article{doi:10.1177/1099636215603036, title = {Dynamic behavior predictions of fiber-metal laminate/aluminum foam sandwiches under various explosive weights}, author = {SB Baştürk and M Tanoğlu and MA Çankaya and OÖ Eğilmez}, url = {https://doi.org/10.1177/1099636215603036}, doi = {10.1177/1099636215603036}, year = {2016}, date = {2016-01-01}, journal = {Journal of Sandwich Structures & Materials}, volume = {18}, number = {3}, pages = {321-342}, abstract = {Application of blast tests causes some problems to characterize the performance of panels due to the drastic conditions of explosive medium. Real test has high safety concerns and is not easily accessible because of its extra budget. Some approaches are needed for the preliminary predictions of dynamic characteristics of panels under blast loading conditions. In this study, the response of sandwiches under blast effect was evaluated by combining quasi-static experiments and computational blast test data. The primary aim is to relate the quasi-static panel analysis to dynamic blast load. Based on this idea, lightweight sandwich composites were subjected to quasi-static compression loading with a special test apparatus and the samples were assumed as single degree-of-freedom mass-spring systems to include dynamic effect. This approach provides a simpler way to simulate the blast loading over the surface of the panels and reveals the possible failure mechanisms without applying any explosives. Therefore the design of the panels can be revised by considering quasi-static test results. In this work, the peak deflections and survivabilities of sandwiches for various explosive weights were predicted based on the formulations reported in the literature. Major failure types were also identified and evaluated with respect to their thicknesses.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Application of blast tests causes some problems to characterize the performance of panels due to the drastic conditions of explosive medium. Real test has high safety concerns and is not easily accessible because of its extra budget. Some approaches are needed for the preliminary predictions of dynamic characteristics of panels under blast loading conditions. In this study, the response of sandwiches under blast effect was evaluated by combining quasi-static experiments and computational blast test data. The primary aim is to relate the quasi-static panel analysis to dynamic blast load. Based on this idea, lightweight sandwich composites were subjected to quasi-static compression loading with a special test apparatus and the samples were assumed as single degree-of-freedom mass-spring systems to include dynamic effect. This approach provides a simpler way to simulate the blast loading over the surface of the panels and reveals the possible failure mechanisms without applying any explosives. Therefore the design of the panels can be revised by considering quasi-static test results. In this work, the peak deflections and survivabilities of sandwiches for various explosive weights were predicted based on the formulations reported in the literature. Major failure types were also identified and evaluated with respect to their thicknesses. |
2014 |
Kandemir, Sinan; Atkinson, Helen V; Weston, David P; Hainsworth, Sarah V METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 45A (12), pp. 5782-5798, 2014, ISSN: 1073-5623. @article{ISI:000342443200049, title = {Thixoforming of A356/SiC and A356/TiB2 Nanocomposites Fabricated by a Combination of Green Compact Nanoparticle Incorporation and Ultrasonic Treatment of the Melted Compact}, author = {Sinan Kandemir and Helen V Atkinson and David P Weston and Sarah V Hainsworth}, doi = {10.1007/s11661-014-2501-0}, issn = {1073-5623}, year = {2014}, date = {2014-11-01}, journal = {METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE}, volume = {45A}, number = {12}, pages = {5782-5798}, abstract = {Thixoforming is a type of semi-solid processing which is based on forming metals in the semi-solid state rather than fully liquid or solid state. There have been no reports of the thixoforming of nanocomposites in the literature. The incorporation of ceramic nanoparticles into liquid metals is a challenging task for the fabrication of metal matrix nanocomposites due to their large surface-to-volume ratio and poor wettability. Previous research work by a number of workers has highlighted the challenges with the incorporation of nanoparticles into liquid aluminum alloy. In the present study, SiC and TiB2 nanoparticles with an average diameter between 20 and 30 nm were firstly incorporated into green compacts by a powder forming route, and then the compacts were melted and treated ultrasonically. The microstructural studies reveal that the engulfment and relatively effective distribution of the nanoparticles into the melt were achieved. The hardness was considerably improved with only 0.8 wt pct addition of the nanoparticles. The nanocomposites were successfully thixoformed at a solid fraction between 0.65 and 0.70. The microstructures, hardness, and tensile mechanical properties of the thixoformed nanocomposites were investigated and compared with those of the as-received A356 and thixoformed A356 alloys. The tensile properties of the thixoformed nanocomposites were significantly enhanced compared to thixoformed A356 alloy without reinforcement, indicating the strengthening effects of the nanoparticles.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Thixoforming is a type of semi-solid processing which is based on forming metals in the semi-solid state rather than fully liquid or solid state. There have been no reports of the thixoforming of nanocomposites in the literature. The incorporation of ceramic nanoparticles into liquid metals is a challenging task for the fabrication of metal matrix nanocomposites due to their large surface-to-volume ratio and poor wettability. Previous research work by a number of workers has highlighted the challenges with the incorporation of nanoparticles into liquid aluminum alloy. In the present study, SiC and TiB2 nanoparticles with an average diameter between 20 and 30 nm were firstly incorporated into green compacts by a powder forming route, and then the compacts were melted and treated ultrasonically. The microstructural studies reveal that the engulfment and relatively effective distribution of the nanoparticles into the melt were achieved. The hardness was considerably improved with only 0.8 wt pct addition of the nanoparticles. The nanocomposites were successfully thixoformed at a solid fraction between 0.65 and 0.70. The microstructures, hardness, and tensile mechanical properties of the thixoformed nanocomposites were investigated and compared with those of the as-received A356 and thixoformed A356 alloys. The tensile properties of the thixoformed nanocomposites were significantly enhanced compared to thixoformed A356 alloy without reinforcement, indicating the strengthening effects of the nanoparticles. |
Sutcu, Mucahit; del Diaz, Juan Jose Coz; Rabanal, Felipe Pedro Alvarez; Gencel, Osman; Akkurt, Sedat Thermal performance optimization of hollow clay bricks made up of paper waste Journal Article ENERGY AND BUILDINGS, 75 , pp. 96-108, 2014, ISSN: 0378-7788. @article{ISI:000337013200010, title = {Thermal performance optimization of hollow clay bricks made up of paper waste}, author = {Mucahit Sutcu and Juan Jose del Coz Diaz and Felipe Pedro Alvarez Rabanal and Osman Gencel and Sedat Akkurt}, doi = {10.1016/j.enbuild.2014.02.006}, issn = {0378-7788}, year = {2014}, date = {2014-06-01}, journal = {ENERGY AND BUILDINGS}, volume = {75}, pages = {96-108}, abstract = {In this paper, the thermal behavior of hollow clay bricks made up of paper waste has been studied and their thermal performance has been optimized. On the one hand, both strength and thermal properties of different paper waste concentrations have been obtained by means of laboratory tests. Thermal conductivity of the microporous brick materials with additives produced in this study reduced from 0.68 W/m K to 0.39 W/m K compared with that of the sample without additives. On the other hand, the finite element method (FEM) has been applied to the nonlinear numerical thermal analysis of three different hollow bricks, including radiation and convection phenomena inside holes. Next, using the design of experiments (DOE) over the FEM models, several parameters such as the material conductivity, the convection and radiation properties and the mean brick temperature have been studied. In general, the thermal resistance is a nonlinear function that depends on the geometry of the recesses, the material properties and the temperature distribution. In all analyzed cases, minimizing the material thermal conductivity of bricks and decreasing the recesses surface radiation emissivity caused a lower thermal transmittance in the brick. Finally, the most important conclusions and the main findings of this research are exposed. (C) 2014 Elsevier B.V. All rights reserved.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this paper, the thermal behavior of hollow clay bricks made up of paper waste has been studied and their thermal performance has been optimized. On the one hand, both strength and thermal properties of different paper waste concentrations have been obtained by means of laboratory tests. Thermal conductivity of the microporous brick materials with additives produced in this study reduced from 0.68 W/m K to 0.39 W/m K compared with that of the sample without additives. On the other hand, the finite element method (FEM) has been applied to the nonlinear numerical thermal analysis of three different hollow bricks, including radiation and convection phenomena inside holes. Next, using the design of experiments (DOE) over the FEM models, several parameters such as the material conductivity, the convection and radiation properties and the mean brick temperature have been studied. In general, the thermal resistance is a nonlinear function that depends on the geometry of the recesses, the material properties and the temperature distribution. In all analyzed cases, minimizing the material thermal conductivity of bricks and decreasing the recesses surface radiation emissivity caused a lower thermal transmittance in the brick. Finally, the most important conclusions and the main findings of this research are exposed. (C) 2014 Elsevier B.V. All rights reserved. |
Kandemir, S; Atkinson, H V; Weston, D P; Hainsworth, S V Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 45 (12), pp. 5782-5798, 2014. @article{Kandemir20145782, title = {Thixoforming of A356/SiC and A356/TiB2 Nanocomposites Fabricated by a Combination of Green Compact Nanoparticle Incorporation and Ultrasonic Treatment of the Melted Compact}, author = {S Kandemir and H V Atkinson and D P Weston and S V Hainsworth}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-84920256211&doi=10.1007%2fs11661-014-2501-0&partnerID=40&md5=fc9071c132a6cd74edb6c9123fe89695}, doi = {10.1007/s11661-014-2501-0}, year = {2014}, date = {2014-01-01}, journal = {Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science}, volume = {45}, number = {12}, pages = {5782-5798}, abstract = {Thixoforming is a type of semi-solid processing which is based on forming metals in the semi-solid state rather than fully liquid or solid state. There have been no reports of the thixoforming of nanocomposites in the literature. The incorporation of ceramic nanoparticles into liquid metals is a challenging task for the fabrication of metal matrix nanocomposites due to their large surface-to-volume ratio and poor wettability. Previous research work by a number of workers has highlighted the challenges with the incorporation of nanoparticles into liquid aluminum alloy. In the present study, SiC and TiB2 nanoparticles with an average diameter between 20 and 30 nm were firstly incorporated into green compacts by a powder forming route, and then the compacts were melted and treated ultrasonically. The microstructural studies reveal that the engulfment and relatively effective distribution of the nanoparticles into the melt were achieved. The hardness was considerably improved with only 0.8 wt pct addition of the nanoparticles. The nanocomposites were successfully thixoformed at a solid fraction between 0.65 and 0.70. The microstructures, hardness, and tensile mechanical properties of the thixoformed nanocomposites were investigated and compared with those of the as-received A356 and thixoformed A356 alloys. The tensile properties of the thixoformed nanocomposites were significantly enhanced compared to thixoformed A356 alloy without reinforcement, indicating the strengthening effects of the nanoparticles. © 2014, The Minerals, Metals & Materials Society and ASM International.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Thixoforming is a type of semi-solid processing which is based on forming metals in the semi-solid state rather than fully liquid or solid state. There have been no reports of the thixoforming of nanocomposites in the literature. The incorporation of ceramic nanoparticles into liquid metals is a challenging task for the fabrication of metal matrix nanocomposites due to their large surface-to-volume ratio and poor wettability. Previous research work by a number of workers has highlighted the challenges with the incorporation of nanoparticles into liquid aluminum alloy. In the present study, SiC and TiB2 nanoparticles with an average diameter between 20 and 30 nm were firstly incorporated into green compacts by a powder forming route, and then the compacts were melted and treated ultrasonically. The microstructural studies reveal that the engulfment and relatively effective distribution of the nanoparticles into the melt were achieved. The hardness was considerably improved with only 0.8 wt pct addition of the nanoparticles. The nanocomposites were successfully thixoformed at a solid fraction between 0.65 and 0.70. The microstructures, hardness, and tensile mechanical properties of the thixoformed nanocomposites were investigated and compared with those of the as-received A356 and thixoformed A356 alloys. The tensile properties of the thixoformed nanocomposites were significantly enhanced compared to thixoformed A356 alloy without reinforcement, indicating the strengthening effects of the nanoparticles. © 2014, The Minerals, Metals & Materials Society and ASM International. |
Kandemir, S; Atkinson, H V; Weston, D P; Hainsworth, S V Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 45 (12), pp. 5782-5798, 2014. @article{Kandemir20145782b, title = {Thixoforming of A356/SiC and A356/TiB2 Nanocomposites Fabricated by a Combination of Green Compact Nanoparticle Incorporation and Ultrasonic Treatment of the Melted Compact}, author = {S Kandemir and H V Atkinson and D P Weston and S V Hainsworth}, url = {https://www.scopus.com/inward/record.uri?eid=2-s2.0-84920256211&doi=10.1007%2fs11661-014-2501-0&partnerID=40&md5=fc9071c132a6cd74edb6c9123fe89695}, doi = {10.1007/s11661-014-2501-0}, year = {2014}, date = {2014-01-01}, journal = {Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science}, volume = {45}, number = {12}, pages = {5782-5798}, abstract = {Thixoforming is a type of semi-solid processing which is based on forming metals in the semi-solid state rather than fully liquid or solid state. There have been no reports of the thixoforming of nanocomposites in the literature. The incorporation of ceramic nanoparticles into liquid metals is a challenging task for the fabrication of metal matrix nanocomposites due to their large surface-to-volume ratio and poor wettability. Previous research work by a number of workers has highlighted the challenges with the incorporation of nanoparticles into liquid aluminum alloy. In the present study, SiC and TiB2 nanoparticles with an average diameter between 20 and 30 nm were firstly incorporated into green compacts by a powder forming route, and then the compacts were melted and treated ultrasonically. The microstructural studies reveal that the engulfment and relatively effective distribution of the nanoparticles into the melt were achieved. The hardness was considerably improved with only 0.8 wt pct addition of the nanoparticles. The nanocomposites were successfully thixoformed at a solid fraction between 0.65 and 0.70. The microstructures, hardness, and tensile mechanical properties of the thixoformed nanocomposites were investigated and compared with those of the as-received A356 and thixoformed A356 alloys. The tensile properties of the thixoformed nanocomposites were significantly enhanced compared to thixoformed A356 alloy without reinforcement, indicating the strengthening effects of the nanoparticles. © 2014, The Minerals, Metals & Materials Society and ASM International.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Thixoforming is a type of semi-solid processing which is based on forming metals in the semi-solid state rather than fully liquid or solid state. There have been no reports of the thixoforming of nanocomposites in the literature. The incorporation of ceramic nanoparticles into liquid metals is a challenging task for the fabrication of metal matrix nanocomposites due to their large surface-to-volume ratio and poor wettability. Previous research work by a number of workers has highlighted the challenges with the incorporation of nanoparticles into liquid aluminum alloy. In the present study, SiC and TiB2 nanoparticles with an average diameter between 20 and 30 nm were firstly incorporated into green compacts by a powder forming route, and then the compacts were melted and treated ultrasonically. The microstructural studies reveal that the engulfment and relatively effective distribution of the nanoparticles into the melt were achieved. The hardness was considerably improved with only 0.8 wt pct addition of the nanoparticles. The nanocomposites were successfully thixoformed at a solid fraction between 0.65 and 0.70. The microstructures, hardness, and tensile mechanical properties of the thixoformed nanocomposites were investigated and compared with those of the as-received A356 and thixoformed A356 alloys. The tensile properties of the thixoformed nanocomposites were significantly enhanced compared to thixoformed A356 alloy without reinforcement, indicating the strengthening effects of the nanoparticles. © 2014, The Minerals, Metals & Materials Society and ASM International. |
2012 |
Sutcu, Mucahit; Akkurt, Sedat; Bayram, Alican; Uluca, Uluc Production of anorthite refractory insulating firebrick from mixtures of clay and recycled paper waste with sawdust addition Journal Article CERAMICS INTERNATIONAL, 38 (2), pp. 1033-1041, 2012, ISSN: 0272-8842. @article{ISI:000300472500020, title = {Production of anorthite refractory insulating firebrick from mixtures of clay and recycled paper waste with sawdust addition}, author = {Mucahit Sutcu and Sedat Akkurt and Alican Bayram and Uluc Uluca}, doi = {10.1016/j.ceramint.2011.08.027}, issn = {0272-8842}, year = {2012}, date = {2012-03-01}, journal = {CERAMICS INTERNATIONAL}, volume = {38}, number = {2}, pages = {1033-1041}, abstract = {Production of porous anorthite refractory insulating firebricks from mixtures of two different clays (K244 clay and fireclay), recycled paper processing waste and sawdust addition are investigated. Suitability of alkali-containing-clay, low-alkali fireclay, pore-making paper waste and sawdust in the products was evaluated. Prepared slurry mixtures were shaped, dried and fired. Highly porous anorthite ceramics from the mixtures with up to 30% sawdust addition were successfully produced. Physical properties such as bulk density, apparent porosity, percent linear change were investigated as well as the mechanical strengths and thermal conductivity values of the samples. Thermal conductivities of the samples produced from fireclay and recycled paper waste decreased from 0.25 W/mK (1.12 g/cm(3)) to 0.13 W/mK (0.64 g/cm(3)) with decreasing density. Samples were stable at high temperatures up to 1100 degrees C, and their cold strength was sufficiently high. The porous anorthite ceramics produced in this study can be used for insulation in high temperature applications. (C) 2011 Elsevier Ltd and Techna Group S.r.l. All rights reserved.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Production of porous anorthite refractory insulating firebricks from mixtures of two different clays (K244 clay and fireclay), recycled paper processing waste and sawdust addition are investigated. Suitability of alkali-containing-clay, low-alkali fireclay, pore-making paper waste and sawdust in the products was evaluated. Prepared slurry mixtures were shaped, dried and fired. Highly porous anorthite ceramics from the mixtures with up to 30% sawdust addition were successfully produced. Physical properties such as bulk density, apparent porosity, percent linear change were investigated as well as the mechanical strengths and thermal conductivity values of the samples. Thermal conductivities of the samples produced from fireclay and recycled paper waste decreased from 0.25 W/mK (1.12 g/cm(3)) to 0.13 W/mK (0.64 g/cm(3)) with decreasing density. Samples were stable at high temperatures up to 1100 degrees C, and their cold strength was sufficiently high. The porous anorthite ceramics produced in this study can be used for insulation in high temperature applications. (C) 2011 Elsevier Ltd and Techna Group S.r.l. All rights reserved. |
2011 |
Basturk, Bahar S; Tanoglu, Metin Mechanical and energy absorption behaviors of metal/polymer layered sandwich structures Journal Article JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 30 (18), pp. 1539-1547, 2011, ISSN: 0731-6844. @article{ISI:000297764900003, title = {Mechanical and energy absorption behaviors of metal/polymer layered sandwich structures}, author = {Bahar S Basturk and Metin Tanoglu}, doi = {10.1177/0731684411421844}, issn = {0731-6844}, year = {2011}, date = {2011-09-01}, journal = {JOURNAL OF REINFORCED PLASTICS AND COMPOSITES}, volume = {30}, number = {18}, pages = {1539-1547}, abstract = {This article considers the sandwich structures with aluminium (Al) foams of various thicknesses in conjunction with skins composed of fibre-metal laminates (FML). The FMLs with Al sheet and glass fiber reinforced polypropylene (GFPP) composites were integrated with Al foam for composing the sandwich panels. The FML-foam sandwich systems were manufactured by hot pressing in a mold at 200 degrees C under 1.5 MPa pressure. The bonding between the components of the sandwich was achieved by various surface modification techniques, i.e., silane surface treatment, PP adhesive film additition, and their combination. The Al sheet/Al foam sandwiches were also prepared by bonding the components with an epoxy adhesive for comparing the effect of GFPP on the mechanical performance of the sandwich structures. The energy absorption capacities together with compressive mechanical behavior of both Al foams and FML-foam sandwich systems were evaluated by flatwise compression tests. Experiments were performed on samples of varying foam thicknesses.}, keywords = {}, pubstate = {published}, tppubtype = {article} } This article considers the sandwich structures with aluminium (Al) foams of various thicknesses in conjunction with skins composed of fibre-metal laminates (FML). The FMLs with Al sheet and glass fiber reinforced polypropylene (GFPP) composites were integrated with Al foam for composing the sandwich panels. The FML-foam sandwich systems were manufactured by hot pressing in a mold at 200 degrees C under 1.5 MPa pressure. The bonding between the components of the sandwich was achieved by various surface modification techniques, i.e., silane surface treatment, PP adhesive film additition, and their combination. The Al sheet/Al foam sandwiches were also prepared by bonding the components with an epoxy adhesive for comparing the effect of GFPP on the mechanical performance of the sandwich structures. The energy absorption capacities together with compressive mechanical behavior of both Al foams and FML-foam sandwich systems were evaluated by flatwise compression tests. Experiments were performed on samples of varying foam thicknesses. |
Yalamac, Emre; Carry, Claude; Akkurt, Sedat Microstructural development of interface layers between co-sintered alumina and spinel compacts Journal Article JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 31 (9), pp. 1649-1659, 2011, ISSN: 0955-2219. @article{ISI:000291143400015, title = {Microstructural development of interface layers between co-sintered alumina and spinel compacts}, author = {Emre Yalamac and Claude Carry and Sedat Akkurt}, doi = {10.1016/j.jeurceramsoc.2011.03.020}, issn = {0955-2219}, year = {2011}, date = {2011-08-01}, journal = {JOURNAL OF THE EUROPEAN CERAMIC SOCIETY}, volume = {31}, number = {9}, pages = {1649-1659}, abstract = {Tests were performed to investigate the microstructure of the interface between alumina and spinel materials after high temperature thermal treatment (1500 degrees C). The first test involved co-sintering of co-pressed alumina and spinel compacts. Microstructures were investigated by SEM, EDS, WDS and EBSD. A microstructurally distinct layer with columnar grains of up to 40 mu m length and 5 mu m width was observed after 16 h at 1500 degrees C. Growth rate of the columnar spinel grains from parent spinet towards alumina follows parabolic kinetics, controlled by a mixed process of O(2-) ion diffusion and interface reaction. Diffusion couples of spinel and alumina were investigated. Same columnar spinel grains were observed at the interface which grew into alumina during thermal treatment with the same kinetics as in co-sintering experiments. The shape of the phase boundaries between spinel and alumina can be a further indication of the direction of their growth. (C) 2011 Elsevier Ltd. All rights reserved.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Tests were performed to investigate the microstructure of the interface between alumina and spinel materials after high temperature thermal treatment (1500 degrees C). The first test involved co-sintering of co-pressed alumina and spinel compacts. Microstructures were investigated by SEM, EDS, WDS and EBSD. A microstructurally distinct layer with columnar grains of up to 40 mu m length and 5 mu m width was observed after 16 h at 1500 degrees C. Growth rate of the columnar spinel grains from parent spinet towards alumina follows parabolic kinetics, controlled by a mixed process of O(2-) ion diffusion and interface reaction. Diffusion couples of spinel and alumina were investigated. Same columnar spinel grains were observed at the interface which grew into alumina during thermal treatment with the same kinetics as in co-sintering experiments. The shape of the phase boundaries between spinel and alumina can be a further indication of the direction of their growth. (C) 2011 Elsevier Ltd. All rights reserved. |
Depboylu, Can O; Yilmaz, Selahattin; Akkurt, Sedat Effects of Catalyst Precursor Type and Preparation Conditions, and Solvent Type on Activity and Selectivity of Pt/SiO2 Catalyst in Citral Hydrogenation Journal Article INTERNATIONAL JOURNAL OF CHEMICAL REACTOR ENGINEERING, 9 , 2011, ISSN: 1542-6580. @article{ISI:000289118100001, title = {Effects of Catalyst Precursor Type and Preparation Conditions, and Solvent Type on Activity and Selectivity of Pt/SiO2 Catalyst in Citral Hydrogenation}, author = {Can O Depboylu and Selahattin Yilmaz and Sedat Akkurt}, issn = {1542-6580}, year = {2011}, date = {2011-01-01}, journal = {INTERNATIONAL JOURNAL OF CHEMICAL REACTOR ENGINEERING}, volume = {9}, abstract = {In this study, citral hydrogenation reaction in liquid phase over silica gel supported Pt catalysts was investigated. It was desired to hydrogenate carbonyl group selectively to produce valuable unsaturated alcohols, namely geraniol and nerol. Pt/SiO2 catalysts were prepared by impregnation method. The effects of parameters investigated in the present study included Pt precursor type (hexachloroplatinic acid (HCLPA), platinum II acetylacetonate (PAA)), catalyst activation temperature (350 degrees C and 450 degrees C), catalyst activation without calcination, catalyst washing with 0.1 M NaOH and solvent type (ethanol, 2-pentanol). The catalysts activities and selectivities were affected by the type of precursor and activation temperature. The maximum citral conversion (89.50 percent) was achieved at lower activation temperature (350 degrees C) with PAA precursor based catalyst. It was observed that higher activation temperature provided lower citral conversion but higher selectivity to unsaturated alcohols; increasing the activation temperature to 450 degrees C decreased citral conversion to 26.10 percent. But selectivity to unsaturated alcohols, geraniol and nerol, increased from 7.06 to 54.60 percent. Catalyst washing and 2-pentanol prevented acetal formation. Catalyst activation without calcination gave lower citral conversion (20.84 percent) and selectivity to unsaturated alcohols (30.00 percent).}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, citral hydrogenation reaction in liquid phase over silica gel supported Pt catalysts was investigated. It was desired to hydrogenate carbonyl group selectively to produce valuable unsaturated alcohols, namely geraniol and nerol. Pt/SiO2 catalysts were prepared by impregnation method. The effects of parameters investigated in the present study included Pt precursor type (hexachloroplatinic acid (HCLPA), platinum II acetylacetonate (PAA)), catalyst activation temperature (350 degrees C and 450 degrees C), catalyst activation without calcination, catalyst washing with 0.1 M NaOH and solvent type (ethanol, 2-pentanol). The catalysts activities and selectivities were affected by the type of precursor and activation temperature. The maximum citral conversion (89.50 percent) was achieved at lower activation temperature (350 degrees C) with PAA precursor based catalyst. It was observed that higher activation temperature provided lower citral conversion but higher selectivity to unsaturated alcohols; increasing the activation temperature to 450 degrees C decreased citral conversion to 26.10 percent. But selectivity to unsaturated alcohols, geraniol and nerol, increased from 7.06 to 54.60 percent. Catalyst washing and 2-pentanol prevented acetal formation. Catalyst activation without calcination gave lower citral conversion (20.84 percent) and selectivity to unsaturated alcohols (30.00 percent). |
2010 |
Yurdakul, Hilmi; Seyhan, Tugrul A; Turan, Servet; Tanoglu, Metin; Bauhofer, Wolfgang; Schulte, Karl Electric field effects on CNTs/vinyl ester suspensions and the resulting electrical and thermal composite properties Journal Article COMPOSITES SCIENCE AND TECHNOLOGY, 70 (14), pp. 2102-2110, 2010, ISSN: 0266-3538. @article{ISI:000283759400010, title = {Electric field effects on CNTs/vinyl ester suspensions and the resulting electrical and thermal composite properties}, author = {Hilmi Yurdakul and Tugrul A Seyhan and Servet Turan and Metin Tanoglu and Wolfgang Bauhofer and Karl Schulte}, doi = {10.1016/j.compscitech.2010.08.007}, issn = {0266-3538}, year = {2010}, date = {2010-11-01}, journal = {COMPOSITES SCIENCE AND TECHNOLOGY}, volume = {70}, number = {14}, pages = {2102-2110}, abstract = {In this study, electrical conductivity of a vinyl ester based composite containing low content (0.05, 0.1 and 0.3 wt.%) of double and multi-walled carbon nanotubes with and without amine functional groups (DWCNTs, MWCNTs, DWCNT-NH2 and MWCNT-NH2) was investigated. The composite with pristine MWCNTs was found to exhibit the highest electrical conductivity. Experiments aimed to induce an aligned conductive network with application of an alternating current (AC) electric field during cure were carried out on the resin suspensions with MWCNTs. Formation of electric anisotropy within the composite was verified. Light microscopy (LM), scanning electron (SEM) and transmission electron microscopy (TEM) were conducted to visualize dispersion state and the extent of alignment of MWCNTs within the polymer cured with and without application of the electric field. To gain a better understanding of electric field induced effects, glass transition temperature (T-g) of the composites was measured via Differential Scanning Calorimetry (DSC). It was determined that at 0.05 wt.% loading rate of MWCNTs, the composites, cured with application of the AC electric field, possessed a higher T-g than the composites cured without application of the AC electric field. (C) 2010 Elsevier Ltd. All rights reserved.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, electrical conductivity of a vinyl ester based composite containing low content (0.05, 0.1 and 0.3 wt.%) of double and multi-walled carbon nanotubes with and without amine functional groups (DWCNTs, MWCNTs, DWCNT-NH2 and MWCNT-NH2) was investigated. The composite with pristine MWCNTs was found to exhibit the highest electrical conductivity. Experiments aimed to induce an aligned conductive network with application of an alternating current (AC) electric field during cure were carried out on the resin suspensions with MWCNTs. Formation of electric anisotropy within the composite was verified. Light microscopy (LM), scanning electron (SEM) and transmission electron microscopy (TEM) were conducted to visualize dispersion state and the extent of alignment of MWCNTs within the polymer cured with and without application of the electric field. To gain a better understanding of electric field induced effects, glass transition temperature (T-g) of the composites was measured via Differential Scanning Calorimetry (DSC). It was determined that at 0.05 wt.% loading rate of MWCNTs, the composites, cured with application of the AC electric field, possessed a higher T-g than the composites cured without application of the AC electric field. (C) 2010 Elsevier Ltd. All rights reserved. |
Budak, Meral; Akkurt, Sedat; Boeke, Hasan Evaluation of heat treated clay for potential use in intervention mortars Journal Article APPLIED CLAY SCIENCE, 49 (4, SI), pp. 414-419, 2010, ISSN: 0169-1317. @article{ISI:000281425700010, title = {Evaluation of heat treated clay for potential use in intervention mortars}, author = {Meral Budak and Sedat Akkurt and Hasan Boeke}, doi = {10.1016/j.clay.2009.11.031}, issn = {0169-1317}, year = {2010}, date = {2010-08-01}, journal = {APPLIED CLAY SCIENCE}, volume = {49}, number = {4, SI}, pages = {414-419}, abstract = {In this study, raw material compositions, basic physical, mineralogical, microstructural and hydraulic properties of lime mortars used in two selected historic buildings were determined by XRD, SEM-EDS and TGA analyses. The results showed that the mortars were hydraulic due to the use of pozzolanic aggregates. Taking into account the hydraulic characteristics of mortars due to the use of pozzolanic aggregates, the possibility of obtaining hydraulic mortars by using pozzolanic aggregates produced from heated commercial clays was investigated. For this purpose, four clay samples used in the ceramic industry in Turkey were heated at varying temperatures of 400, 450, 500, 550, 600, 800, and 1200 degrees C with a heating rate of 10 degrees C/min. Pozzolanic properties of heated clay samples were determined. The results showed that commercial clays studied are well suited for use as pozzolanic aggregates when they are heated between 500 and 700 degrees C. This is also confirmed by testing the compressive strengths of the three month aged laboratory-produced mortars that contained thermally treated clay (at 600 degrees C) as pozzolanic aggregates. Compressive strength of this mortar was around 5 MPa which is satisfactorily high. (C) 2009 Elsevier B.V. All rights reserved.}, keywords = {}, pubstate = {published}, tppubtype = {article} } In this study, raw material compositions, basic physical, mineralogical, microstructural and hydraulic properties of lime mortars used in two selected historic buildings were determined by XRD, SEM-EDS and TGA analyses. The results showed that the mortars were hydraulic due to the use of pozzolanic aggregates. Taking into account the hydraulic characteristics of mortars due to the use of pozzolanic aggregates, the possibility of obtaining hydraulic mortars by using pozzolanic aggregates produced from heated commercial clays was investigated. For this purpose, four clay samples used in the ceramic industry in Turkey were heated at varying temperatures of 400, 450, 500, 550, 600, 800, and 1200 degrees C with a heating rate of 10 degrees C/min. Pozzolanic properties of heated clay samples were determined. The results showed that commercial clays studied are well suited for use as pozzolanic aggregates when they are heated between 500 and 700 degrees C. This is also confirmed by testing the compressive strengths of the three month aged laboratory-produced mortars that contained thermally treated clay (at 600 degrees C) as pozzolanic aggregates. Compressive strength of this mortar was around 5 MPa which is satisfactorily high. (C) 2009 Elsevier B.V. All rights reserved. |
Sutcu, Mucahit; Akkurt, Sedat; Okur, Salih A microstructural study of surface hydration on a magnesia refractory Journal Article CERAMICS INTERNATIONAL, 36 (5), pp. 1731-1735, 2010, ISSN: 0272-8842. @article{ISI:000278432800035, title = {A microstructural study of surface hydration on a magnesia refractory}, author = {Mucahit Sutcu and Sedat Akkurt and Salih Okur}, doi = {10.1016/j.ceramint.2010.02.043}, issn = {0272-8842}, year = {2010}, date = {2010-07-01}, journal = {CERAMICS INTERNATIONAL}, volume = {36}, number = {5}, pages = {1731-1735}, abstract = {Hydration of the surface of a periclase refractory was studied in a controlled humidity atmosphere (92% relative humidity) at 26 degrees C for up to 92 h. The effect of humidity on the specimens was examined using a scanning probe microscope (SPM) and a scanning electron microscope (SEM), which showed that the degree of hydration was noticeably less in the intergranular bond phase compared to the periclase crystallites. The SPM study indicated significant growth of hydrates on the refractory grain surface. Growth rate of the hydrate layer was least on (0 0 1) orientation, higher for the (1 0 3) orientation, and highest for the (1 0 1) oriented grain. The rate of loss of refractory phases by hydration on a (1 0 1) oriented grain was 4.53 nm/h. This material loss may be insignificant for a bulk brick, but is a serious threat for a magnesia castable consisting of fine magnesia powder due to large surface area exposed to humidity or water itself. (C) 2010 Elsevier Ltd and Techna Group S.r.l. All rights reserved.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Hydration of the surface of a periclase refractory was studied in a controlled humidity atmosphere (92% relative humidity) at 26 degrees C for up to 92 h. The effect of humidity on the specimens was examined using a scanning probe microscope (SPM) and a scanning electron microscope (SEM), which showed that the degree of hydration was noticeably less in the intergranular bond phase compared to the periclase crystallites. The SPM study indicated significant growth of hydrates on the refractory grain surface. Growth rate of the hydrate layer was least on (0 0 1) orientation, higher for the (1 0 3) orientation, and highest for the (1 0 1) oriented grain. The rate of loss of refractory phases by hydration on a (1 0 1) oriented grain was 4.53 nm/h. This material loss may be insignificant for a bulk brick, but is a serious threat for a magnesia castable consisting of fine magnesia powder due to large surface area exposed to humidity or water itself. (C) 2010 Elsevier Ltd and Techna Group S.r.l. All rights reserved. |
Sutcu, Mucahit; Akkurt, Sedat Utilization of recycled paper processing residues and clay of different sources for the production of porous anorthite ceramics Journal Article JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 30 (8), pp. 1785-1793, 2010, ISSN: 0955-2219. @article{ISI:000276563600003, title = {Utilization of recycled paper processing residues and clay of different sources for the production of porous anorthite ceramics}, author = {Mucahit Sutcu and Sedat Akkurt}, doi = {10.1016/j.jeurceramsoc.2010.01.038}, issn = {0955-2219}, year = {2010}, date = {2010-06-01}, journal = {JOURNAL OF THE EUROPEAN CERAMIC SOCIETY}, volume = {30}, number = {8}, pages = {1785-1793}, abstract = {Production of porous anorthite ceramics from mixtures of paper processing residues and three different clays are investigated. Suitability of three different clays such as enriched clay, commercial clay and fireclay for manufacturing of anorthite based lightweight refractory bricks was studied. Porous character to the ceramic was provided by addition of paper processing residues (PPR). Samples with 30-40 wt% PPR fired at 1200-1400 degrees C contained anorthite (CaO center dot Al2O3 center dot 2SiO(2)) as major phase and some minor secondary phases such as mullite (3Al(2)O(3)center dot 2SiO(2)) or gehlenite (2CaO center dot Al2O3 center dot SiO2), depending on the calcite to clay ratio. Anorthite formation for all clay types was quite successful in samples with 30-40 wt% of paper residues fired at 1300 degrees C. A higher firing temperature of 1400 degrees C was needed for the fireclay added samples to produce a well sintered product with large pores. Gehlenite phase occurred mostly at lower temperatures and in samples containing higher amount of calcium (50 wt% PPR). Compressive strength of compacted and fired pellets consisting of mainly anorthite ranged from 8 to 43 MPa. (C) 2010 Elsevier Ltd. All rights reserved.}, keywords = {}, pubstate = {published}, tppubtype = {article} } Production of porous anorthite ceramics from mixtures of paper processing residues and three different clays are investigated. Suitability of three different clays such as enriched clay, commercial clay and fireclay for manufacturing of anorthite based lightweight refractory bricks was studied. Porous character to the ceramic was provided by addition of paper processing residues (PPR). Samples with 30-40 wt% PPR fired at 1200-1400 degrees C contained anorthite (CaO center dot Al2O3 center dot 2SiO(2)) as major phase and some minor secondary phases such as mullite (3Al(2)O(3)center dot 2SiO(2)) or gehlenite (2CaO center dot Al2O3 center dot SiO2), depending on the calcite to clay ratio. Anorthite formation for all clay types was quite successful in samples with 30-40 wt% of paper residues fired at 1300 degrees C. A higher firing temperature of 1400 degrees C was needed for the fireclay added samples to produce a well sintered product with large pores. Gehlenite phase occurred mostly at lower temperatures and in samples containing higher amount of calcium (50 wt% PPR). Compressive strength of compacted and fired pellets consisting of mainly anorthite ranged from 8 to 43 MPa. (C) 2010 Elsevier Ltd. All rights reserved. |
Proje Adı | Proje Yöneticisi | Başlangıç Tarihi | Destekleyen Kuruluş |
| Karbon Nanotüp (CNT) / Poliester Nanokompozitlerin Geliştirilmesi | Prof. Dr. Metin Tanoğlu | 2004 | JÜLICH, Almanya - TÜBİTAK |
| Tenzorezistörlerin Düşük Termohassasiyet Termal Katsayısı İle Geliştirilmesi | Prof. Dr. Metin Tanoğlu | 2002 | NATO |
| Havacılık uygulamaları için yapısal kompozit parçaların yenilikçi yaklaşımlar ile birleştirilme yöntemlerinin geliştirilmesi, çevresel etkilere dayanım ve mekanik performansının karakterize edilmesi | Prof. Dr. Metin Tanoğlu | 2019 | TÜBİTAK |
| Alüminyum Köpük Metal Dolu Alüminyum ve Kompozit Tüplerin Ezilme Davranışları | Prof. Dr. Mustafa Güden | 2004 | TÜBİTAK |
| Çapraz-kama haddeleme prosesinin teknik özelliklerinin Türk ve Belarus Endüstrileri için detaylandırılması | Prof. Dr. Mustafa Güden | 2010 | TÜBİTAK |
| Çok Katmanlı Malzemelerde Dalga Geçişi | Prof. Dr. Mustafa Güden | 2003 | NSF - TÜBİTAK |
| Frit Fırını Refrakterlerinin İzotermal Korozyon Testi | Prof.Dr.Sedat Akkurt | 2005 | TÜBİTAK |
| Grafen Nanolevha Takviyeli Metal Matrisli Nanokompozitlerin Geliştirilmesi | Yrd. Doç. Dr. Sinan Kandemir | 2015 | TÜBİTAK |
| Kil /EPDM Esaslı Nanokompozitlerin Geliştirilmesi | Prof. Dr. Metin Tanoğlu | 2006 | ARÇELİK A.Ş. - TÜBİTAK |
| Kompozit Malzemelerin Örgüsüz Cam / Termoplastik Hibrid Elyaflardan Geliştirilmesi | Prof. Dr. Metin Tanoğlu | 2010 | TÜBİTAK |
| Nanokompozit Malzemelerin Polimer ve Tabakalı Kil Yapılardan Geliştirilmesi ve Karakterizasyonu | Prof. Dr. Metin Tanoğlu | 2005 | TÜBİTAK |
| Patlama Etkisine Karşı Koruyucu Zırh Geliştirmesi | Prof. Dr. Metin Tanoğlu | 2008 | Milli Savunma Bakanlığı ve TÜBİTAK |
| Seramik Matriks Kompozitlerin Düşük Sıcaklıklarda Polimer Pyroliz Yöntemi İle Üretimi ve Karakterizasyonu | Prof. Dr. Metin Tanoğlu | 2002 | TÜBİTAK |
| Sic-Parçacık Takviyeli Alüminyum Köpük Metal Üretimi ve Karakterizasyonu | Prof. Dr. Mustafa Güden | 1998 | TÜBİTAK |
| Sic-Vıskırlı Aluminium Köpüklerin Hazırlanması | Prof. Dr. Mustafa Güden | 2003 | TÜBİTAK |
| Antibakteriyel Kompoze Taş Üretimi | Prof. Dr. Metin Tanoğlu | 2014 | SANTEZ |
| Gelişmiş Kemik Entegrasyonu Sağlayan Yeni Gözenekli ve Köpük Ti6Al4V Spinal Kafes İmplatların Tasarımı ve İmalatı | Prof. Dr. Mustafa Güden | 2009 | SANTEZ |
| Otomotiv Sektörüne Yönelik Kompozit Malzeme Esaslı Yaprak Yay Sistemlerinin Tasarımı ve Üretim Tekniklerinin Geliştirilmesi | Prof. Dr. Metin Tanoğlu | 2014 | SANTEZ |
| Ege Bölgesi Beylikler Dönemi Tarihi Yapılarındaki Özgün Harçların Karakterizasyonu ve Restorasyonlarda Kullanılacak Onarım Harçlarının Laboratuvarda Hazırlanması | Prof.Dr.Sedat Akkurt | 2003 | DPT |
| Fonksiyonel Dereceli Sic-Parçacık Takviyeli Alüminyum Matris Kompozit Malzemelerin Toz Metalürjisi Yöntemi İle Hazırlanması ve Statik ve Dinamik Özelliklerinin Mekanik ve Ultrasonik Yöntemlerle Ölçülmesi | Prof. Dr. Mustafa Güden | 2003 | DPT |
| Kompozit Zırh Malzemelerinin Geliştirilmesi | Prof. Dr. Metin Tanoğlu | 2003 | DPT |
| Akma ile Kalınlaşan Sıvı Zırh Sistemlerinin Geliştirilmesi | Prof. Dr. Metin Tanoğlu | 2014 | Savunma Sanayi Müsteşarlığı Projesi |
| İmplant Uygulamaları Için Ti Köpük Malzemelerin Hazırlanması | Prof. Dr. Mustafa Güden | 2003 | HİPOKRAT |
| Seramik Vitrifiye Ürünlerin Yüksek Basınçlı Dökümü Için Gözenekli Malzemelerin Geliştirilmesi ve Karakterizasyonu | Prof. Dr. Metin Tanoğlu | 2001 | EGE VİTRİFİYE A.Ş |
| Çoklu Alüminyum Kapalı Hücreli Köpük Dolu Alüminyum ve Polimerik Kompozit Tüplerin Ezilme Davranışlarının Belirlenmesi | Prof. Dr. Mustafa Güden | 2003 | İYTE-BAP |
| FP Aluminium Uzun Fiber Takviyeli Magnesium Kompozitlerin Deformasyon Hızına Bağlı Mekanik Davranışları | Prof. Dr. Mustafa Güden | 2003 | İYTE-BAP |
| Hafif, Düşük Maliyetli Polimer Esaslı Kompozit Malzemelerin Üretim Teknolojilerinin Yerleştirilmesi ve Savunma Sanayi Ne Yönelik Kompozit Zırh Malzemelerin Geliştirilmesi | Prof. Dr. Metin Tanoğlu | 2001 | İYTE-BAP |
| Jeotermal Uygulamalar İçin Polimerik Kompozit Boru Malzeme Mikroyapısısnın Malzeme Dayanım, Mekanik ve Termal Özelliklerine Etkisi | Prof. Dr. Metin Tanoğlu | 2002 | İYTE-BAP |
| Kölemanit Ilkavesiyle Kaolen Ve Kalsitten Anortit Seramikleri Sentezlenmesi ve Sinterlenmesi | Prof.Dr.Sedat Akkurt | 2004 | İYTE-BAP |
| Korozyona Uğramış Manyezit-Bazlı Çimento Fırını Refrakterlerin Mikroyapısal Karakterizasyon | Prof.Dr.Sedat Akkurt | 2001 | İYTE-BAP |
| Krom Manyezit Çimento Fırını Refrakterlerinde Bulunan Demirce Zengin Halkaların İncelenmesi | Prof.Dr.Sedat Akkurt | 2002 | İYTE-BAP |
| Nanokompozit malzemelerin geliştirilmesi ve karakterizasyonu | Prof. Dr. Metin Tanoğlu | 2003 | İYTE-BAP |
| Sinterlenmiş Yüksek Saflıktaki Alüminanın Bof Curuflarıyla Korozyonunun Laboratuvar İncelemesi | Prof.Dr.Sedat Akkurt | 2001 | İYTE-BAP |
| Spinel ve Alüminanın Düşük Sıcaklıkta Üretiminde Mekanokimyasal Sentezin Kullanılması | Prof.Dr.Sedat Akkurt | 2002 | İYTE-BAP |
| Titanyum Esaslı Açık Hücreli Köpük Metal Üretim Proses Parametrelerinin ve Mekanik Özelliklerinin Belirlenmesi | Prof. Dr. Mustafa Güden | 2004 | İYTE-BAP |
| Yüksek Balistik Dayanımlı Kompozit Hafif Zırh Malzemelerinin Geliştirilmesi | Prof. Dr. Metin Tanoğlu | 2002 | İYTE-BAP |
